ap radio

ConfigDot11 wlan 1Vlan 1Ssid testExitInt g0/1En d 1ExitInt d 1/0En d 1Wlan-id 1ExitInt bvi 1Ip add 10.1.1.1 255.255.255.0EndWrIf multiple WLANs are required, you must configure them on the RF sub-interface.Ruijie (config) # sh runBuilding configuration...Current configuration: 2877 bytes!Version RGOS 10.4 (1T13), Release (128463) (Mon JAN 5 08:57:05 CST 2009-ngcf65)!!!!NfppNo nd-guard enable!!!Vlan 1!Vlan 4!!No service password-encryptionService dhcpIp fragment-quota 200!Ip dhcp excluded-address

Input radio button: adding a property to the radio button tag 0 means not selectedHTML code:inputname= "Rdo1"value= "AA"type= "Radio"Tag= "0" />ABR/>inputname= "Rdo2"value= "BB"type= "Radio"Tag= "0" />BBR/>inputname= "Rdo3"value= "CC"type= "Radio"Tag= "0" />Cjquery Code: $ (

Welcome to the network technology community forum and interact with 2 million technical staff to enter the Windows system. By default, the "any available network" option is automatically selected, however, this option requires the support of Wireless AP devices. If we do not have the support of Wireless AP devices, this option cannot be selected. Similarly, "Access Point only (structure) network option Wel

In Linux, the wireless network card is used to set up an AP. Due to the need of the experiment, we need to set up a Wireless AP. After a long time, we finally finished the setup. Www.2cto.com my machine is equipped with two NICs, the wired Nic is connected to the network through the network, and there is also a wireless Nic, as a Wireless AP. Because madwifi driv

As network devices develop, many products are gradually moving towards integration. For example, some routing, some integrating cat functions, and some integrating switch functions. This article will introduce how to change a wireless router to a Wireless AP through configuration and debugging. Comparison In a sense, a Wireless AP is equivalent to a wireless Hub. The main difference between a Wireless

Step One Install the wireless network card driver and client software, after the installation is complete, as shown in the following figure. Step Two Enable the analog AP feature. 1. Select the advanced option in the client software. 2. Softap mode , select " open ", prompt "Confirm open Softap mode", click " Confirm ". The "Setting up Softap mode" is displayed, and then you are prompted "You are setting up Softap mode success." 3. Confi

First, you must have a wireless NIC driver on the arm Development Board! The 2.6 kernel supports more than 10 wireless Nic chips. When buying NICs, the last chip is available in the Linux Kernel! It is troublesome to find a proper driver! Next we will run the command to connect to the AP. I used the Vista system to set up a simulated AP point mode to ad-hoc (this should all be simulated as point-to-point

1, check whether the wireless network card support virtual AP (Support does not support the hosting network). Note: Does not support, also can not use up, the following tutorial also does not have to look! Start---run (win+r), enter CMD, and open the Command window. Enter in command specifier: Netsh wlan show drive Have you seen the "Supported hosting network: Yes" This one, this NIC is supported! 2, through the command to establish a "wirele

Tp-link wr720n wireless AP Mode Setup Tutorial Step 1: Connect to tl-wr720n. Because tl-wr720n in AP mode by default does not open the DHCP server, can not automatically assign IP address to the computer, so need to configure the computer wireless network connection IP address, in order to log on the router's management interface. Set the computer wireless network connection IP address to 192.168.1.X (2≤x≤

Obtains the value of a set of radio selected items. Var item = $ ('input [@ name = items] [@ checked] '). val (); Obtain the text of the selected select item. Var item = $ ("select [@ name = items] option [@ selected]"). text (); The second element in the select drop-down box is the selected value. $ ('# Select_id') [0]. selectedIndex = 1; The second element of the radio Group is the currently selected valu

Because this part is "The daily use of jquery", so all are from the specific needs, summed up the need to use the knowledge points. The code is not written well enough to achieve the goal. So let's take a look at this demand first: color block mode based on color mode, that is, open color to open the color block, color is closed when the color block is not available, open color when the color block radio usable, close color if the color block is open

First, use to get the selected value to determine the selected Directly on the code, don't forget to refer to the jquery package Copy Code code as follows: Radio cannot be judged by "checked" equality, only by using true Copy Code code as follows: Second, use the checked attribute to judge the selected Radio cannot be judged by "checked" equality, only by usi

This article relies on jquery, the first of which is implemented using jquery, and the third is based on JS and Dom, and interested friends can understand This article provides three ways to deselect radio, as shown in the following:nbsp; nbsp; This article relies on jquery, the first of which is implemented using jquery, and the third is based on JS and Dom. nbsp; Code as follows: ;nbsp;

This article provides three ways to deselect radio, as shown in the following code example: This article relies on jquery, the first of which is implemented using jquery, and the third Way is based on JS and Dom. Copy Code code as follows:

There are many related articles about wireless device installation. Here, we will summarize the installation ideas for a wide audience of readers. We hope to help you clarify your ideas and configure your devices so that wireless Internet access is unobstructed. To connect a wireless LAN to the Internet, the most important thing is to have a terminal connected to the Internet, which is a wireless router or Wireless AP. The biggest difference between t

"Network Environment"650) this.width=650; "title=" 1.jpg "alt=" wkiom1vezaggsld2aacrlz5kcr4869.jpg "src=" http://s3.51cto.com/wyfs02/M02/ 6c/4b/wkiom1vezaggsld2aacrlz5kcr4869.jpg "/>"AP Version"This feature is supported only if the version is greater than 11.ConfigurationVersion 11.1 (5) B3Hostname ap-513!Fair-schedule!IP access-list Standard 10Ten Permit any!Web-auth Template IportalPage-suite DefaultAuthe

AP Plet is a small application written in the Java language that can be embedded in HTML and interpreted by the WWW browser. But how do you handle the vast amounts of data in the Internet world and the various resources that are distributed across the Internet in AP Plet? This is going to use JDBC. First, the working principle of JDBC JDBC (Java DataBase connectivity) is a Java application interface for e

There was a problem with setting up WiFi hotspots on Ap-hotspot on Ubuntu 14.04 today. After you have configured the SSID and key, run sudo apt-mark hold HOSTAPD after you have been in the sudo apt-mark for HOSTAPD status. Later found a solution, hope to see this article's friends can also successfully solve:First, we install Ap-hotspot:sudo add-apt-repository ppa:nilarimogard/webupd8sudo apt-get updatesudo