arduino textbook

Modify the SSID and passwd, the program burned to 8266, waiting for the serial port to return the successful connection message, after the successful connection can see the return of an IP address, using the browser azimuth this IP address can see

void Setup () {} void Loop () {} small light flashing void Setup () {Pinmode (2,output);} void Loop () {Digitalwrite (2,lo W);//light delay (1000); Digitalwrite (2,high);//Control PIN level delay (1000); /////////////////////////////////////////////

#include #include #include #include #include & Lt mailbox.h> #include #include #include #include IPAddress Server (10,0,0,9); Yunclient client; String Parametri = ""; String of POST parameters void Setup () {bridge.begin

After the study number two #define COM_HEAR 2 #define COM_SOUND 3 #define Com_speak 4 void Setup () {Pinmode (Com_sound, OUTPUT); Pinmode (Com_speak, OUTPUT); Pinmode (Com_hear, INPUT); Serial.begin (9600); } void Loop () {int I, j, K; int

Using the library's tasks feature, there are three things to do first: First: Reference Library#include "SCoop.h""Library File Download

Human infrared module is very simple, is the normal three-pin (vcc,gnd,data), the data is high, low level, that is, there are only two results: High level for the active body is detected, low level for no active human detection. It is important to

1. Turn 45 per joint, reciprocating cycle#include void setup () {setposition (1,511);//set the position of servo # 1 to ' 511 ' setposition (2,5 11); SetPosition (3,511); SetPosition (4,511); SetPosition (5,400);

Hello everyone, I'm a small-story.Remember the previous section click the Open linkToday we talk about sensors.Today, we talk about light and ultrasound.Send a picture first:The light sense has three interfaces, namely:UCC, out, GND.The ultrasound

Reprinted please indicate the source: http://blog.csdn.net/lxk7280 First, contact the kinectorbit camera library. The download URL and brief introduction of this library are provided in this article: http://blog.csdn.net/lxk7280/article/details/3818

I wrote it here, but it hasn't been tested yet. 1. Move the two ends of the led to the center and return to the two sides. 1 // adr301.ino 2 3 byte ledPin[] = {4, 5, 6, 7, 8, 9, 10, 11, 12, 13}; 4 int ledDelay(65); 5 int direction = 1; 6 int

The board we got two days ago. The first test is 18b20, but the value cannot be read. At first, I directly connected the analog port. Later I realized that this was not a simulated sensor, but a number. It is switched to a digital port. analog

  Connect as shown in the following figure:   The resistor size of the photosensitive resistor is inversely proportional to the brightness. By measuring the voltage of the resistor, you can know the resistor size of the photosensitive resistor to

In the past SCM programming process, probably most people are more familiar with the MCU WiFi module and the server to establish a socket connection. However, it may be a better option to establish an HTTP connection when we are confronted with the

/* Write by Qingtai Jiang Leftleg.write (95); Leftfoot.write (100); Rightleg.write (80); Rightfoot.write (64); Delay (s); State 1 Initial angle #define AA 88//Rudder initial angle left upper rudder #define BB 89//Left Lower rudder

Thermistor Connection method: Resistance: / * * thermistor model is NTC glass-sealed thermal resistor mf58-104f 3950K interpolation 100K accuracy 1% b value 3950 * Room temperature 25 degrees Celsius (298.15K) resistance is 100k euro */ #

SummaryWhile learning about the radio, I learned that Arduino was a good choice for my next Raspberry Pi as a skill not yet mature technology. So spent 200 yuan to buy 3 pieces of Arduino Development Board (2*NANO1*UNO) and other sensors, but also see the 315M Super-regeneration module, because play radio know 315M is the car remote control, anti-theft gate, road and bridge system, such as the most commonly

data to the channel, and the other device can receive the data in the channel. Of course, for the establishment of this channel connection is a certain condition, that is, the Bluetooth set up to be able to connect the at mode0x0:softwareserial LibraryThe existing Arduino hardware supports pin 0 and 1 (connected to the computer via USB) for serial communication. The serial is carried out via a hardware called UART (chip built-in). This hardware allow

Using JavaScript to manipulate hardware has long been a rarity. So as an electronic professional origin of Fe, I also intend to try to use JS to drive Arduino; To operate these underlying hardware, there must be some tools, and the tools I'm introducing here are mainly Cylonjs and Gort. Cylonjs is actually a operation "machine" JS framework, the official website of the introduction is such: Cylon.js is a JavaScript framework for robotics, physical

that the two efforts to cultivate more internet professionals, for the development of science and technology to make more contributions.The use of microcomputer to develop student programming education has been common,Arduino, Galileo and other micro-computer Development Board manufacturers are also trying to devote to the field of computer programming education, this October, BBC Micro: The production company of Bit mini computer equipment distribut

the rapid development of Internet and the rise of IoT in the world, a new mode of operation is also quietly born, that is, web of things, referred to as WOT. It can be understood as part of the IoT, centralizing the Web-based control and management of resources in the Internet of things, including gateways and gateway-based sensors, with the main thrust of promoting direct access to the resources of smart terminals and gateways through the rest Web API. Users can access the data resources of th