best imu for arduino

Thermistor Connection method: Resistance: / * * thermistor model is NTC glass-sealed thermal resistor mf58-104f 3950K interpolation 100K accuracy 1% b value 3950 * Room temperature 25 degrees Celsius (298.15K) resistance is 100k euro */ #

1. Turn 45 per joint, reciprocating cycle#include void setup () {setposition (1,511);//set the position of servo # 1 to ' 511 ' setposition (2,5 11); SetPosition (3,511); SetPosition (4,511); SetPosition (5,400);

Hello everyone, I'm a small-story.Remember the previous section click the Open linkToday we talk about sensors.Today, we talk about light and ultrasound.Send a picture first:The light sense has three interfaces, namely:UCC, out, GND.The ultrasound

Reprinted please indicate the source: http://blog.csdn.net/lxk7280 First, contact the kinectorbit camera library. The download URL and brief introduction of this library are provided in this article: http://blog.csdn.net/lxk7280/article/details/3818

I wrote it here, but it hasn't been tested yet. 1. Move the two ends of the led to the center and return to the two sides. 1 // adr301.ino 2 3 byte ledPin[] = {4, 5, 6, 7, 8, 9, 10, 11, 12, 13}; 4 int ledDelay(65); 5 int direction = 1; 6 int

The board we got two days ago. The first test is 18b20, but the value cannot be read. At first, I directly connected the analog port. Later I realized that this was not a simulated sensor, but a number. It is switched to a digital port. analog

  Connect as shown in the following figure:   The resistor size of the photosensitive resistor is inversely proportional to the brightness. By measuring the voltage of the resistor, you can know the resistor size of the photosensitive resistor to

In the past SCM programming process, probably most people are more familiar with the MCU WiFi module and the server to establish a socket connection. However, it may be a better option to establish an HTTP connection when we are confronted with the

/* Write by Qingtai Jiang Leftleg.write (95); Leftfoot.write (100); Rightleg.write (80); Rightfoot.write (64); Delay (s); State 1 Initial angle #define AA 88//Rudder initial angle left upper rudder #define BB 89//Left Lower rudder

[Csharp]/*************************************** **************************** Program name: Mega_ADK ADC** Parameter count: None** Function: Send the voltage value (mv) collected by AD through the serial port)** Note: The target board is Maga adk

The simplest example:   Void setup () { Serial. Begin (9600); // open the serial port and set the baud rate to 9600 bps. } Void loop () { Int val; Val = analogread (5 );//The sensor is connected to the analog Port 5, and the value is

Modify the SSID and passwd, the program burned to 8266, waiting for the serial port to return the successful connection message, after the successful connection can see the return of an IP address, using the browser azimuth this IP address can see

void Setup () {} void Loop () {} small light flashing void Setup () {Pinmode (2,output);} void Loop () {Digitalwrite (2,lo W);//light delay (1000); Digitalwrite (2,high);//Control PIN level delay (1000); /////////////////////////////////////////////

#include #include #include #include #include & Lt mailbox.h> #include #include #include #include IPAddress Server (10,0,0,9); Yunclient client; String Parametri = ""; String of POST parameters void Setup () {bridge.begin

After the study number two #define COM_HEAR 2 #define COM_SOUND 3 #define Com_speak 4 void Setup () {Pinmode (Com_sound, OUTPUT); Pinmode (Com_speak, OUTPUT); Pinmode (Com_hear, INPUT); Serial.begin (9600); } void Loop () {int I, j, K; int

Using the library's tasks feature, there are three things to do first: First: Reference Library#include "SCoop.h""Library File Download

Human infrared module is very simple, is the normal three-pin (vcc,gnd,data), the data is high, low level, that is, there are only two results: High level for the active body is detected, low level for no active human detection. It is important to

read MPU6050 data under Arduino Reference: http://diyhacking.com/arduino-mpu-6050-imu-sensor-tutorial/ hardware Arduino uno or Arduino mega2560 MPU6050 sensor (GY-521 or GY-9150) DuPont line several connections Note: If you use

device and the ground planeIn the whole article I try to minimize the math operations. If you know what the sine, cosine, and tangent functions are, you should understand and use the ideas in this article regardless of which platform your project uses, such as Arduino, Propeller, Basic Stamp, ATEML chip, pic chip, and so on. Some people think that the use of IMU units requires complex mathematical operatio

between the device and the ground planeIn the whole article I try to minimize the math operations. If you know what the sine, cosine, and tangent functions are, you should understand and use the ideas in this article regardless of which platform your project uses, such as Arduino, Propeller, Basic Stamp, ATEML chip, pic chip, and so on. Some people think that the use of IMU units requires complex mathemati