bgp routing table

Because only one default gateway is allowed under Windows 2000, if the local connection (intranet) is connected with the Internet in the Network Neighborhood--〉 attribute, the local connection 2 (extranet) is equipped with the Internet 10.42.29.10, on the surface it is configured with 2 gateways, However, in the DOS environment, enter the route print command to view the routing table, and there is only one

Administrator mode cmdRouting Table Interpretationroute print -4Remove default settingsroute delete 0.0.0.0Outside the network, all the wireless, 192.168.0.1 for the wireless gatewayroute add 0.0.0.0 mask 0.0.0.0 192.168.0.1 –pInternal network by, all-in-wire, 192.168.12.1 for wired gatewaysroute add 192.168.0.0 mask 255.255.0.0 192.168.12.1 –p转自：https://zhuanlan.zhihu.com/p/22266906Windows routing

Recently in the toss of the route command, a momentary preface clears the routing table, as in the following commandRoute -F Then the egg hurts, localhost and 127.0.0.1,ping can not open, finally found a command on the Internet, reset the IPv4 protocol, as followsnetsh int IPv4 reset After execution, restarting the computer is finally normal./* As long as you run this line, * *Here's how the route works, th

); - if(op[0]=='A'){ inaa++; - for(intj=0;j4; j + +) toA[aa].x= (a[aa].x8)|read (); +A[aa].l=read (); - } the Else{ *qq++; $ for(intj=0;j4; j + +)Panax NotoginsengQ[qq].x= (q[qq].x8)|read (); -Q[qq].l=read (), q[qq].r=read (); the Insert (q[qq].x); + } A } the } + voidGetmark (intPOS) { - intp=0; $ for(intI= +;i> +-a[pos].l;i--){ $ intT=a[pos].x>> (I-1) 1; - if(!trie[p][t])return; -p=Trie[p][t]; the } -

1. Open Start Menu-run-Enter cmd, then click OK2. Enter the command to add a route in the following interface: Route add needs to divert IP mask 255.255.255 local export IP. The following is an example of the need to shunt IP 8.8.8.8, local export IP192.168.0.1. (Enter the command after entering the key, if the installation of 360 prompts, choose to allow all the operation of this program). You can add success3, confirm whether to add success, directly in the following input command: route print

Route-eNetstat-nrMan 8 routeThe appearance of the routing table|destination|gateway|genmask|flags|mss|window|irtt|iface||::||| destination network or destination host| gateway or "*" indicates no set | The mask of the destination net, all 255 represents a host address, and 0.0.0.0 represents a default route | U: Routing up, h means the target is a host, g means u

NetstatNetwork status, displaying information such as native network connections, running ports, and routing tablesRelated options　　 -A display native all connections and listening ports　　- N Displays the currently established valid connections and ports in the form of a network IP address　　- r Display routing table information　　- T display TCP protocol connectio

Linux dual-line IP settings (no additional routing table required, just modify the following OK)ModifyVi/etc/iproute2/rt_tables(Increase the number of telecom and netcom two routing tables)Increase252 Tel (Telecom)251 CNC (netcom)(Set up telecom and Netcom routing table cont

error message: vmsvc[xxxx]:[warning][guestinfo]recordroutinginfo:unable to collect IPv4 routing tableThe following components are properly installed after checking that:Linuxvmos properly installed;IP information is set correctly;vmwaretools properly installed;the virtual machine hardware version is 9;Restart The VM, the boot process prompted libguestinfo.so module failure will prompt, but the VM still start normally, but it will hung live 1, 20 minut

Reference: https://www.tecmint.com/ip-command-examples/Learn the configuration IP of Linux, configure the gateway, add routes and other commandsman ipman ip addressman ip routeip address help可简写ip a sOperations Viewing interfaces- 查看所有接口ip+macip a- 查看eth0的ip+macip a s eth0- 给一个接口设置多个ip(ip addr add)ip a a 12.1.1.1/24 dev eth0ip a a 13.1.1.1/24 dev eth0- 删除一个接口的ipip a d 13.1.1.1/24 dev eth0- 持久化配置到文件(wr)ip address save 1> b.txtip address restore Operation Rou