bonding link aggregation

192.168.10.0Network 192.168.20.0 tells neighbors that they know the IPNetwork 192.168.30.0Network 11.0.0.0ar1========================================================================================Interface Eth-trunk3 into Eth-trunk3Undo Portswitch Switch from two-layer mode to layer threeIP address 11.0.0.2 255.255.255.0 set IP to Eth-trunk3#Interface gigabitethernet0/0/0Eth-trunk 3 Add interface to Eth-trunk 3 (link

Original intention: At the beginning of 2011, when I learned about the switch link aggregation technology, I had a question in my mind: The switch receives a message, arrives at the aggregation mouth, how chooses the member mouth to go out? Was it a random selection? or by the number of members from small to large or from the big round? If you choose the sourc

VTP (link aggregation Protocol)Vtp vlan TrunkingProtocol VLAN link aggregation protocol in a switching network with multiple switches, the same VLAN is usually configured on multiple switches, and the same configuration is also performed on multiple interfaces, to configure the same VLAN on multiple vswitches, VTP tran

Why is link aggregation recommended in virtualized network design? The reasons are as follows: 650) this.width=650; "src=" Http://s4.51cto.com/wyfs02/M00/7F/C0/wKioL1crUxSAgOT0AAOWRxDKRHE016.jpg "style=" float:right; "Title=" PSB (1). jpg "alt=" wkiol1cruxsagot0aaowrxdkrhe016.jpg "/>1. First, link aggregation technolog

Topology: Cisco 3750 === H3C 3600Note:1. When both interfaces 3750 are pagp and 3600 are lacp, the Port-channel status is down.2. When one interface in 3750 is pagp and the other is lacp, the two interfaces are not aggregated and the link peer communicates with each other through consistent protocols.Conclusion:When configuring link aggregation, the interfaces at

Tutorial topology: 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M00/47/BF/wKiom1P_THjC8klUAAFlyn6ovHE323.jpg "Title =" 1.png" alt = "wkiom1p_thjc8kluaaflyn6ovhe323.jpg"/> R3 is a gateway, R4 is an egress router, and DHCP is used. R5 is a vro on the Internet. Lab requirements: 1. Three PCs belong to three VLANs 2. R1 and R2 are used for Link aggregation. 3. The Gateway ends at R3 to implement

, and it is a technique for organizing network layer IP addresses in a hierarchical way so that addresses have "topological importance." Main performance: First, once the aggregation network segment of a network is added to the zone, all the internal routes of the IP addresses that fall within the aggregation segment are no longer broadcast independently to other regions, but only the routing information o

RHEL7 network adapter link aggregation and grub troubleshooting tutorial, rhel7grub 1. Nic link Aggregation NIC teaming, simply put, is to bind multiple physical ports together as one logical port for higher bandwidth and load balancing or high availability. In RHEL7, runner (which can be regarded as a piece of code) i

DTP (Dynamic Link aggregation Protocol)The dynamic link aggregation protocol (DTP) of DTPDTP (dynamic trunking protocol) is a Cisco private Point-to-Point protocol used to dynamically negotiate the port type as Access or Trunk. To complete automatic negotiation, Port 2 must be in the same VTPdomain. The DTP frame is se

Lab Requirements:The dual-core architecture combines three-layer switching technology with VTP, STP, and Ethernet channels to achieve high-speed network conversion, high availability, high reliability and redundant backup functions, mainly for the network of dual-core topologies.Experimental design:1. Configure VLANs on the switch to control broadcast traffic.2. Configure the Ethernetchannel between the 2 three-layer switches to achieve high-speed interoperability between the three-layer switche

Link Aggregation (linkaggregation) is the "bundle" of physical link sections with the same transport media type, the same transmission rate, logically looking like a link. Link aggregation, also known as a relay (trunking), allows

I. Introduction to link Aggregation1. TIC TeamingBind multiple physical ports together as a logical portRhel7 is high availability or load balancing through runner (which can be seen as a piece of code)2. Team structureMster: A logical port that can be viewed as a groupSlave: All physical ports, which can be considered as members3. Team Implementation ProcessConfigure a mster(logical port) and set the mode (HA or LB) simultaneously via runnerbind the

Red Hat Enterprise Linux 5-a network interface bound in link aggregation mode cannot use the given DHCP address Define a network interfaceBond0For example, and useIfcfg-bond0The configuration file is as follows: Device = bond0Bootproto = DHCPType = BondingOnboot = YesUserctl = NoBonding_opts = "miimon = 100 mode = 4 lacp_rate = 1 xmit_hash_policy = 1" Two Ethernet devices have been configured to belong to t

-FC1AABkHhvUeZY091.jpg "style=" float: none; "title=" 9.jpg "alt=" Wkiol1zwj8aq-fc1aabkhhvuezy091.jpg "/>Modify Ifcfg-team0-port1 and the Ifcfg-team0-port2 configuration file and remove excess information9.Restart the software bridge to activate Team0systemctl Restart NetworkRestartsystem, ping Gateway test connectivity via Team0 interface650) this.width=650; "src=" http://s2.51cto.com/wyfs02/M02/77/E0/wKiom1ZwJ8DxSueoAACw_evX6fI631.jpg "style=" float: none; "title=" 11.jpg "alt=" Wkiom1zwj8dxsu

Rhel7 Aggregation LinkProgramme one:Sometimes the state can not see, add ethnet, restart the network and then delete.650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/74/55/wKioL1YaY7fAL9mZAABWrWC4zCw542.jpg "/>650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/74/58/wKiom1YaY5vT4ASHAABKmKb_8KE748.jpg "/>650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/74/58/wKiom1YaY5vw5n4KAABWmF2yY9E200.jpg "/>650) this.width=650; "src=" h