cisco 1900 router

we are using Console connect the router and the computer, start the router and use the Putty connect to the router's console ( Console ), it is recommended that you first configure the hostname of the router ( hostname ) To facilitate identification, configure the privileged mode ( Enable ) Password and vty ( telnet ) password to protect the

In chapter 3 of the Cisco router manual, we will explain the "setup dialog process". This article is taken from the manual. This makes it easier for you to focus on setting up conversations. Global parameter settings, interface parameter settings, and display results. Setting Dialog can avoid the hassle of manually entering commands, but it cannot completely replace manual settings, some special settings mu

When the cisco router is powered on normally, perform the following steps: 1. Test the router hardware When a cisco router is started, a hardware self-check program POST is initiated. This program checks basic hardware functions including CPU, memory, and network interface

At present, China's wireless router industry is developing very rapidly, and its market demand is also very high. Here we mainly introduce Cisco's first dual-band wireless router launched in China, this section describes the features and performance of the vro. In May 19, Cisco launched the Linksys by Cisco dual-band w

The first of these methods This approach restores the following routers: Cisco 2000 series, 2500 series, 3000 series, Cisco 4000 series using the 680x0 Motorola CPU, and 10.0 series routers running 7000 versions of Cisco IOS systems. Implementation steps: 1. Connect a terminal at the console port of the router or a

Initial installation of the CISCO router tutorial During the first installation, the system automatically enters the Dialog Setup, as prompted on the screen, answer the router name, encrypted super login password, super login password, remote login password, dynamic routing protocol, and the configuration of each interface, and save the configuration. After the v

Telnet remote Login Configuration 1, configure Cisco router login account, password, account level, as shown below, account name ABC, password for abc123, account level of 15 (highest level) R1#configure Terminal R1 (config) #username ABC privilege secret abc123 R1 (config) #end r1# 2, configure the Cisco router

Cisco router ip nat command ip natip nat inside destination ip nat inside source list ip nat inside source static ip nat outside source list ip nat outside source static ip nat pool ip nat translation ip nat Syntax: ip nat {inside | outside} no ip nat {inside | outside} this command is used to set the Intranet and Internet interfaces for applying NAT. Use the no option to stop the interface from applying NA

Topology map: 1. Configure the router R4 as a Frame relay switch Frame-relay switching * configured as Frame Relay switch 2. Configure the interface's clock frequency, package type, LMI type and Frame Relay DCE on the router R4 int s0/0 No shut Clock rate 64000 * Set clock frequency Encapsulation Frame-relay * Encapsulated as Frame Relay Frame-relay lmi-type

This article mainly uses an example to explain in detail how to solve the packet loss problem caused by CISCO router faults? The following article gives me a detailed answer. Recently, some people in my department (Department A) reported that they could not access the network of the higher-level department (Department B. I use the ping command from the computer A1 (IP Address: 10.20.12.11/24) used by this p

A Cisco router uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4, And the L2 Switch uses two Cisco 2950, A layer-3 Switch uses a Cisco 3550. There are two VLANs in the network. To simplify the descriptio

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one