cisco 1921 router

First, give an environment:Cisco router Intranet interface s1/0: 192.168.1.1 255.255.255.0Internet interface s1/1: 10.0.0.1 255.255.255.0Server ip Address: 192.168.1.100First telnet to the vrotelnet:User Access Verification Username: cisco # enter the user namePassword: # enter the PasswordRouter> en # Enter privileged ModePassword: # enter the privileged mode PasswordRouter # conf t # enter global configur

Analysis of Cisco router IOS backup and recovery Introduction: I. Wiring Serial Interface-> console and pc Nic interfaces-> F0/0 // The IP address of the PC and the F0/0 interface (of course, other interfaces can be connected to the network cable). The IP address can be in the same network segment. You can also use an Internet ip address! Ii. Tools 3 CDaemon (tftp server) and CRT (access routing tool) Iii.

Here we will mainly introduce the configuration and initial installation of Cisco routers. Describes how to configure Cisco router settings and remote access, this article discusses how to use the DHCP service function of the internal network to allocate address information for users who remotely dial in and how to troubleshoot common vro faults. 1. Initial insta

When the iOS corruption in router needs to be restored, Ctrl+break (Packettrace is CTRL + C) When the router starts, enters Rommon mode, and the command prompt changes to: Rommon 1>Then enter the following command:Rommon 1>IP_ADDRESS=A.B.C.D//router's current IP addressRommon Subnet mask for 2>ip_subnet_mask:x.x.x.x//routerRommon 3>default_gateway=y.y.y.y//Router

Release date:Updated on: Affected Systems:Cisco ASR 9006Cisco ASR 9006Description:--------------------------------------------------------------------------------Bugtraq id: 48811Cve id: CVE-2011-2549 Cisco ASR 9000 series is an integrated service router solution that uses the Cisco ios xr Software module operating system to provide carrier-level reliability.

In this experiment, the speed limiting device of a Cisco router is completed by a Cisco2811 router. In this experiment, we will first look at the flash: www.2cto.com yourname # dirDirectory of flash on the router in two ways: /1-rw-25438028 Oct 22 2010 02:25:58 + 02:26:08 c2800nm-ipbase-mz.124-15.T.bin2-rw-1505280 Oct

, dynamic address translation, and multiplexing dynamic address translation. The following example uses a Cisco router.1. Static address translationStatic address translation performs one-to-one conversion between the internal local address and the internal legal address, and specifies the legal address to which the conversion is required. If there are WWW servers or FTP servers in the internal network that

1. Use the ip verfy unicast reverse-path network interface command This function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the router discards the packet if it does not have a route from the source IP address of the packet. For example, if the

Vro is a commonly used network device. I believe everyone knows the importance of backing up the cisco router configuration file. Next we will introduce how to use the COPY command to back up the cisco router configuration file, and how to COPY and back up the cisco

1. TELNET Remote logon Configuration 1. Configure the Logon account, password, and account level on the CISCO router, as shown below. The account name is abc, the password is abc123, And the account level is 15 to the highest level) R1 # configure terminal R1 (config) # username abc privilege 15 secret abc123 R1 (config) # end R1 # 2. Configure the remote logon authentication mechanism for the

that needs to be mapped to the Internet for access by others. The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step 1:First First, ensure that the server and PC can ping the gateway GW, then perform NAT on the GW, and ensure that t

When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available. Check on the Internet, the original switch port is Switchport, that is, the two-layer swit

1. Preface A large number of Cisco routers are used in Jiangxi IP networks. Administrators usually use Telnet to remotely log on to the vro for routine maintenance. Because Telnet, FTP, and other network service programs use plain text transmission passwords and data in the network, their security cannot be effectively guaranteed. Once the Administrator's user name and password are intercepted by someone with ulterior motives, the consequences will b

The VPN configuration of the Cisco router is not important for network security, but also makes the user more convenient during use. In this experiment, we use the Cisco 2600 router and the Cisco router VPN configuration to implem

I. Overview: In the actual work can often see a strong SSL VPN can bypass deployment, and support routing mode and NAT mode: Router mode requires intranet to VPN assigned address pool address can be router; NAT mode, VPN Client access intranet host, intranet host sees address as VPN interface address, Therefore, the address intranet of the VPN address pool is not required to be routed. If you want to test

Cisco router startup process:(1) execute Bootstrap Loader in the ROM, which is similar to the BIOS in the computer and Bootstrap will install IOS into RAM;(2) IOS can be stored in many places (FLASH, TFTP server or ROM). The order in which the router looks for IOS images depends on the startup domain of the configuration register and other settings. Configuration

Cisco router register configuration objective: Register configuration is used to change the router startup process. The Start bit consists of four hexadecimal registers. The value range of 0 xABCD www.2cto.com ranges from 0x0 to 0 xFFFF 0x2102: Industrial default value 0x2142: starts from FLASH, but do not use the configuration file (for Password Recovery) in NVR

When a Cisco router forgets or loses the enable password, there are two methods to restore it, depending on the series of products you are using.Method 1Steps:1. Connect a terminal or a PC with simulation terminal software installed on the console port of the router.The default register value is 0x2102. The value ranges from the third digit to the left. If it is 1, it is disableBreak. If it is 0, the Break

Cisco router ACL wildcard192.168.1.20-192.168.1.50 range of networksA contiguous address, the form of a wildcard mask must be:11111111=25501111111=12700111111=6300011111=3100001111=1500000111=700000011=300000001=1For range 20-50, be sure to use Access-list 1 per 192.168.1.0 0.0.0.63, then go head to tail0-16 the maximum block address that can be contained is 16:access-list 1 deny 192.168.1.0 0.0.0.1516-19

) #interface gigabitethernet0/0.1Router (config-subif) #encapsulation dot1q 2Router (config-subif) #ip address 192.168.1.1 255.255.255.0DhcpWanglei (config) #ip DHCP excluded-address 192.168.1.1Wanglei (config) #ip DHCP pool dhcppool1Wanglei (dhcp-config) #network 192.168.1.0 255.255.255.0Wanglei (dhcp-config) #default-router 192.168.1.1Wanglei (dhcp-config) #dns-server 192.168.1.1Wanglei (dhcp-config) #dns-server 61.128.114.133Static NATRouter (confi