cisco 2504

Using Cisco to build an experimental environment I.. Configure DHCP client;Two, configure the switch SW1SW1 (config) #vlan 10SW1 (Config-vlan) #exSW1 (config) #vlan 20SW1 (Config-vlan) #exSW1 (config) #int FA0/1SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 10SW1 (config-if) #no shutdownSW1 (config) #int FA0/2SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 20SW1 (config-if) #eSW1 (config

"Introduction" Within a switched network, it is possible to segment and organize flexibly through VLANs. VLANs can group devices in a LAN. A group of devices in a VLAN communicates as if it were connected to the same line. VLANs are based on logical connections, not physical connections. Types of VLANsThere are many different types of VLANs used in modern networks. Some VLAN types are defined by traffic category. Some other VLAN types are defined by specific features.Data VLAN: used to deliver u

Automatic backup and fallback of Cisco iOS profiles requires the use of the Archive Archive configuration mode feature of iOS. In general, only the version number of iOS has the Archive configuration mode feature in 12.3 (4) Cisco iOS profile automatic backup All commands are as follows: router> Router>enable Router#configure Terminal Router (config) #archive Router (config-archive) #write-memory

Trunk Link Trunk: Same inter-VLAN communication on different switchesHow to play tag tag encapsulationPackage Type: IEEE 802.1q/cisco ISLIEEE 802.1q:4 Bytes, internal encapsulation, publicCisco isl:30 bytes External encapsulation, privateSwitch port configuration mode: Trunk/acces (OFF)/Dynamic desirable/dynamic AutoTwo auto NO mode of operation generally either trunk or accessEthernet Channel: Multiple physical ports to form a logical port for greate

(HSRP)Direct Connect Ping PassTarena-r1 (config) #interface f0/0TARENA-R1 (config-if) #standby 1 IP 192.168.1.254TARENA-R1 (config-if) #standby 1 priority 200 PrioritiesTARENA-R1 (config-if) #standby 1 preempt preemptive rightTARENA-R1 (config-if) #standby 1 track F0/1 port trackingTarena-r2 (config) #interface f0/0TARENA-R2 (config-if) #standby 1 IP 192.168.1.254 act as IPTARENA-R2 (config-if) #standby 1 priority 195 PrioritiesTARENA-R2 (config-if) #standby 1 preempt preemptive rightTARENA-R2

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1

  Sometimes I feel like I am a genius ~ O (worker _ worker) O ~, A little encouragement. (Although it's a big question... maybe) 1 # include 2 int gcd (int m, int N) 3 {4 return M = 0? N: gcd (N % m, m); 5} 6 int main () 7 {8 int N; 9 scanf ("% d"

/*Time Limit: 1000/1000 ms (Java/other) memory limit: 32768/32768 K (Java/other)Total submission (s): 148 accepted submission (s): 19Font: Times New Roman | verdana | GeorgiaFont size: bytes →Problem descriptionThere are three positive integers A, B,

Idea: Find one by one. Because C is not equal to B and B is the maximum common divisor of (a, c), C is an integer multiple of B, every time a C is found, it determines whether the maximum common divisor of A is B. If not, continue. At the beginning,

One of my customers has a VPN which I 'd like to access. they provided me with a copy of the Cisco VPN Client for Linux, and a "PCF" configuration file for the client. here's what I had to do to get the Cisco VPN Client working in Linux-and it does work just fine. First we make a directory to put the bits and bobs in alan@hactar:~$ mkdir ciscoalan@hactar:~$ cd cisco