cisco 2950 router

Cisco router configuration manual Virtual LAN (VLAN) routing 1. The main network technology we currently use when constructing an enterprise network is generally based on exchange and virtual networks. The exchange technology changes shared media to exclusive media, greatly improving the network speed. The Virtual Network Technology breaks the restrictions of the geographical environment. without changing t

Cisco router has become a commonly used network device, but we are not very clear about its storage classification. Here we will introduce it in detail. Memory category: 1: RAM: Random Access to memory, equivalent to computer memory 2: ROM: read-only memory. Some microcodes used to start and maintain the router are resident in the ROM. 3: FLASH Memory, equiva

CISCO Router Network Address Translation (NAT)Tutorial name: Cisco Router Network Address Translation (NAT) objective: to connect all Intranet IP addresses to the Internet using a small number of public IP addresses. Tutorial Introduction: using NAT technology, when an intranet private address sends data packets to a v

Tags: Cisco CCNA router Password managementfor device security, the device administrator typically sets the user name and password for the device. Here's how to configure 3 passwords, with emphasis in the middle.Username Test password Cisco//This is to set up a layer of accounts and passwordsEnable password 123// This is the Setup admin passwordRouter (config) #l

In the Cisco router product, we usually need to use restricted access for general users when we initially configure. This is very important for routers, by default, our router is an open system, access control options are turned off, any user can log on to the device for further attack, so we need our network administrator to configure the password to restrict un

: single two-way authentication: www.2cto.com 2.2, CHAP authentication: CHAP: Challenge Handshake Authentication Protocol, full name: challenge Handshake Authentication Protocol. CHAP verifies the identity of the authenticated end through a three-way handshake. It is completed when the initial link is established. To improve security, it is periodically verified after the link is established. CHAP is safer than PAP because CHAP does not send plain text online, but instead sends a random number s

This article uses VPN technology to achieve interconnection between two parts of the network, simulate ISP, close to practicality, the article mainly shows us the specific operation steps, mainly the input of basic commands. In this experiment, we use the Cisco 2600 router and VPN technology to achieve the network interconnection between one branch and two parts. To stay close to practicality, we still use

Cisco port status: CSU ── channel server unit, DSU ── data server, unit, DTE ── DataTerminalEquipment 1. Serial * is down, line protocol is down (DTE) faults: [1] No power is added to the vro. [2] LINE is not connected to CSU/DSU. [3] hardware error. Solution: [1] Check power supply. [2] Check whether the cables and serial ports used are correct. [3] switch to another serial port. 2. Serial * is up and line protocol is down (DTE) faults: [1] local or

...Writing monlib sectors........................................................................................................Monlib Write complete Format:all system sectors written. Ok...Format:operation completed successfully. Format of Flash:completeProgram load complete, entry point:0x8000f000, size:0xcb80(5) TFTP to see if iOS upload is complete.(6) Rommon 8 > Reset//Restart routerCisco

Cisco router IOS upload and download 1. Prepare a console line and a network cable. The connection cable is connected to the console port of the computer. The network cable is connected to the computer and the F0/0 port of the router. (Only F0/0 can be used. The router has no system, the IP address configured for the

To emulate the password of the reset router with the Cisco Packet Tracer Simulator, the packet tracer default router port is off and needs to be manually enabled 650) this.width=650; "Src=" http://s3.51cto.com/ Wyfs02/m01/5a/21/wkiol1t3xxiqjwmeaakcapd2ghs648.jpg "title=" 2.png "alt=" Wkiol1t3xxiqjwmeaakcapd2ghs648.jpg "/>1. Shut down the

Global debugging When configuring a Cisco router, the boundaries between global and interface commands are obvious. In this case, we use "Global" to identify commands that cannot be used for interface debugging or specific transmission media types and Protocol debugging. For example, in vrouters 2500, you can use Debugging commands to analyze the Cisco Discovery

RIP and IGRP are commonly used router configuration protocols. What problems should we pay attention to when configuring RIP and IGRP? What should we do? The following configuration steps provide detailed answers. RIP Protocol RIP (Routing information Protocol) is an Internal Gateway Protocol (IGP) that is widely used earlier and is suitable for small-sized similar networks, is a typical distance-vector protocol. For more information, see RFC1058 an

1. Preparation Tools Cisco TFTP server, HyperTerminal, iOS files iOS files are not easy to find, you need to look at the hardware version, as well as the size of ROM RAM, to my Cisco 2621XM for example (with two fastethernet),Start looking for a few 2600 of iOS, the brush is not correct, the problem of unrecognized network interface, can not be configured, there should be F interface with S Ios,

Some time ago, someone familiar with me asked me how to set up a bridge on a Cisco router )? At that time, due to the relationship between work, I just briefly talked to him. Today, we set up a Cisco router as a complete configuration command for bridging. Through this instance, you can learn how to use a

address of the TFTP server be entered. After the Server IP address is correctly entered, the router also requires the network administrator to provide the configuration file name to be backed up. Generally, we recommend that you use a file name that is easily remembered by the Administrator. At this time, the router will prompt the Administrator to press YES to confirm the operation. 3. copy tftp running-c

CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access. Task commands Set the PPP encapsulation ppp1 Set the authentication method ppp authentication {chap | chap pap | pap cha

This article describes how to control the BT traffic of a Cisco router through specific operations, and describes the specific operation methods in detail. I hope this article will help you. Network-Based Application Recognition (NBAR) indicates Network Application Recognition. NBAR is a technology that can dynamically search for protocols in Layer 4 to Layer 7. It can not only control static and simple net

are used The route of this packet. ---- GRE only provides encapsulation of data packets. It does not have encryption to prevent network listening and attacks. Therefore, in the actual environment, it often corresponds to an IP address. When the SEC is used together, IPSec provides encryption of user data to provide users with better security. The GRE protocol has two main purposes: internal protocol encapsulation and private address encapsulation. In China, CEN uses almost all TCP/IP protocols,

Probably a lot of people on the Cisco router speed limit is not a special understanding, so I studied the Cisco router speed limit detailed settings statement, here to share with you, I hope to be useful. In a Cisco router device,