cisco 2950 router

Analysis of Cisco router IOS backup and recovery Introduction: I. Wiring Serial Interface-> console and pc Nic interfaces-> F0/0 // The IP address of the PC and the F0/0 interface (of course, other interfaces can be connected to the network cable). The IP address can be in the same network segment. You can also use an Internet ip address! Ii. Tools 3 CDaemon (tftp server) and CRT (access routing tool) Iii.

Here we will mainly introduce the configuration and initial installation of Cisco routers. Describes how to configure Cisco router settings and remote access, this article discusses how to use the DHCP service function of the internal network to allocate address information for users who remotely dial in and how to troubleshoot common vro faults. 1. Initial insta

At present, China's wireless router industry is developing very rapidly, and its market demand is also very high. Here we mainly introduce Cisco's first dual-band wireless router launched in China, this section describes the features and performance of the vro. In May 19, Cisco launched the Linksys by Cisco dual-band w

The first of these methods This approach restores the following routers: Cisco 2000 series, 2500 series, 3000 series, Cisco 4000 series using the 680x0 Motorola CPU, and 10.0 series routers running 7000 versions of Cisco IOS systems. Implementation steps: 1. Connect a terminal at the console port of the router or a

Initial installation of the CISCO router tutorial During the first installation, the system automatically enters the Dialog Setup, as prompted on the screen, answer the router name, encrypted super login password, super login password, remote login password, dynamic routing protocol, and the configuration of each interface, and save the configuration. After the v

Telnet remote Login Configuration 1, configure Cisco router login account, password, account level, as shown below, account name ABC, password for abc123, account level of 15 (highest level) R1#configure Terminal R1 (config) #username ABC privilege secret abc123 R1 (config) #end r1# 2, configure the Cisco router

Release date:Updated on: Affected Systems:Cisco ASR 9006Cisco ASR 9006Description:--------------------------------------------------------------------------------Bugtraq id: 48811Cve id: CVE-2011-2549 Cisco ASR 9000 series is an integrated service router solution that uses the Cisco ios xr Software module operating system to provide carrier-level reliability.

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one

255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all

Cisco routers are widely used in network interconnection. Among them, 2500 series routers are widely used in low-end users. So what if you accidentally forget the superuser password of the 2500 series router? Don't be afraid, as long as you can restore as follows:Preparation: a computer running Terminal simulation program can start a Super Terminal in Windows 95/98), and the microcomputer serial port COM1/C

1. Use the ip verfy unicast reverse-path network interface command This function checks each packet passing through the router. In the CEF (Cisco Express Forwarding) Table of the router, the router discards the packet if it does not have a route from the source IP address of the packet. For example, if the

The Cisco router NAC solves the problem. The so-called NAC is an architecture that allows multiple hardware and software components to work together to protect the user's network from adverse client attacks. 1. It is not easy to fully implement NAC, because the entire architecture contains too many different components from other vendors. For example, the architecture contains the NAC Policy Manager and mul

Vro is a commonly used network device. I believe everyone knows the importance of backing up the cisco router configuration file. Next we will introduce how to use the COPY command to back up the cisco router configuration file, and how to COPY and back up the cisco

1. TELNET Remote logon Configuration 1. Configure the Logon account, password, and account level on the CISCO router, as shown below. The account name is abc, the password is abc123, And the account level is 15 to the highest level) R1 # configure terminal R1 (config) # username abc privilege 15 secret abc123 R1 (config) # end R1 # 2. Configure the remote logon authentication mechanism for the

1. Preface A large number of Cisco routers are used in Jiangxi IP networks. Administrators usually use Telnet to remotely log on to the vro for routine maintenance. Because Telnet, FTP, and other network service programs use plain text transmission passwords and data in the network, their security cannot be effectively guaranteed. Once the Administrator's user name and password are intercepted by someone with ulterior motives, the consequences will b

:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interface mode, and configure the Ip-> activation in