cisco 3500 router

NAT configuration on a CISCO router is in full swing and causes the shortage of IP addresses. to alleviate this problem, an important application is NAT (Network Address Translation ), it is widely used. Through address translation, NAT enables enterprises to access the Internet by using only a small number of valid IP addresses on the internet, effectively alleviating address insufficiency, at the same tim

Configure PPPoE for connecting a CISCO router to an ADSL modem using the Cisco router: hostname bjsite! Ip subnet-zero no ip domain-lookup! Vpdn enable no vpdn logging! Vpdn-group 1 request-dialin protocol pppoe! Interface Ethernet0/0 ip address 192.168.0.1 255.255.255.0 ip nat inside no ip mroute-cache!!!! Interface E

1. Preparation Tools Cisco TFTP server, HyperTerminal, iOS files iOS files are not easy to find, you need to look at the hardware version, as well as the size of ROM RAM, to my Cisco 2621XM for example (with two fastethernet),Start looking for a few 2600 of iOS, the brush is not correct, the problem of unrecognized network interface, can not be configured, there should be F interface with S Ios,

CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access. Task commands Set the PPP encapsulation ppp1 Set the authentication method ppp authentication {chap | chap pap | pap cha

This article describes how to control the BT traffic of a Cisco router through specific operations, and describes the specific operation methods in detail. I hope this article will help you. Network-Based Application Recognition (NBAR) indicates Network Application Recognition. NBAR is a technology that can dynamically search for protocols in Layer 4 to Layer 7. It can not only control static and simple net

are used The route of this packet. ---- GRE only provides encapsulation of data packets. It does not have encryption to prevent network listening and attacks. Therefore, in the actual environment, it often corresponds to an IP address. When the SEC is used together, IPSec provides encryption of user data to provide users with better security. The GRE protocol has two main purposes: internal protocol encapsulation and private address encapsulation. In China, CEN uses almost all TCP/IP protocols,

Probably a lot of people on the Cisco router speed limit is not a special understanding, so I studied the Cisco router speed limit detailed settings statement, here to share with you, I hope to be useful. In a Cisco router device,

CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common

Preparation: A PC with a TFTP server, a router with iOS, and a cable connectionSet the router interface and the IP address of the computer card on the same network segment, and can ping each other.1 , install Cisco TFTP Server2 , set the TFTP log path and file storage pathNote: During the entire download process, TFTP server cannot shut down3 , Configure the IP o

Tags: Cisco router forgot enable passwordSteps:1. Restart the router that appears on the router ROM Monitor mode, press "Ctrl+breack" Key to enter ROM mode, such as:650) this.width=650; "title=" capture. PNG "style=" float:left; "alt=" Wkiol1nkiftr_sdkaaa1fp9kntk338.png-wh_50 "src=" https://s4.51cto.com/wyfs02/M00/A7

This article describes how to enhance the security of a Cisco router by using a Nipper. So how should we use it? The following article gives you a detailed answer. How do I use a Nipper? Since Nipper supports so many devices and is also known to support a wide range of multi-functional options, it is impossible for me to present them in all aspects. However, we can make a basic demonstration. In our example

One. Test the topology:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/CA/wKiom1WH46fhBjvJAADX2zoss3k937.jpg "title=" TP1. JPG "alt=" Wkiom1wh46fhbjvjaadx2zoss3k937.jpg "/>Two. Test ideas:A. Enable resolution by IP NAT without setting the direction---this way can be accessed directly from the public IP address, or can be accessed by domain name method---unfortunately Cisco is different iOS, some although have IP nat enable, but do not re

Necessity for configuring WRED on a Cisco Router Although the queue provides VoIP QoS congestion management, it still needs some congestion avoidance mechanisms, such as WRED. In particular, WRED can prevent the output queue from reaching the limit value, which will lead to the loss of all input packets. This article comes from Informit and discusses the necessity of configuring WRED on a

Cisco once again launched a new generation of router products and also applied new technologies. So I studied how Cisco developed the new VQE technology to solve the problem of IPTV Video Delivery. Here I will share it with you, I hope it will be useful to you. Cisco has announced the release of the VisualQualityExperi

Cisco IOS is a dedicated kernel that provides routing, switching, network interconnection, and remote communication capabilities. Most Cisco routers are running iOS, and more and more Cisco Catalyst switches are running it, including Catalyst2960 and Catalyst3560 series switches. Some important aspects of the Cisco

Implementation of VPN on a Cisco router: 1. software requirements: IOS with performaniseplusistmc56 is required. Currently, stable versions are 12.07T2. Hardware requirements: 8 mbflashand40mbram in DownloadIOS, the software and hardware requirements of the downloaded IOS version are prompted. 3. IPSec manual method considerations Implementation of VPN on a Cisco

China Mobile's GPRS network uses the APN method to connect to the GPRS device terminal and communicate with the server through the APN. The customer purchased the Cisco 2811 router, and the mobile company needed to pull the optical fiber through the E1 port, I spent more than 1000 RMB with an E1 module. mobile companies are doing very poorly, and optical fiber connectors are not provided at all. I also boug

For Cisco router authentication, when performing the cisco Route Selection protocol (r12002; VPN) authentication, the key is irrelevant to the key ID when using plain text (General authentication, during MD5 authentication, the key and key ID are related, that is, the key IDs and keys at both ends must be the same, for example, R1 (config) # key chain key1 R1 (co

Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685)Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685) Release date:Updated on:Affected Systems: Cisco ASR 1000 Description: CVE (CAN) ID: CVE-2015-0685The

In Cisco router configurations, NAT configurations are frequently used. I hope the introduction below will be helpful to the majority of fans. It is a common method. The vro performs simple NAT translation and sets a CIDR Block in the NAT address pool. After a while, I found that the address pool was a waste of time. When I wanted to use a real ip address, I couldn't use it, so I decided to modify the