cisco 3650 switch

Configuration of a layer-3 Cisco switch 1. Start a route on a layer-3 switch. Otherwise, layer-3 switch does not have the routing function switch (config) # ip routing2. Configure the VLAN ip address switch (config) # interface vl

There was just one Cisco 2960 switch that failed this afternoon, replacing an alternate switch immediately, but the backup switch was transferred back from another branch and the password was forgotten. Just use the recovery password process, also share it.1. Set the Windows HyperTerminal, name customization. Recommend

The Cisco router switch sets automatic backup for IOS files and restores the automatic backup and rollback of Cisco IOS configuration files. The archive configuration mode function of IOS is required. Generally, only IOS versions 12.3 (4) All commands for automatic backup of the Cisco IOS configuration file are as foll

Tags: Cisco switchBasic configuration and management of switches• Technical Principles• The switch is managed in two basic ways: in-band management and out-of-band management.• The console port management switch through the switch is out-of-band management, which does not occupy the network port of the

Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the corresponding port. for frames without target MAC ing/Target wide (Group) broadcasting, SW learns diff

message are correctIf a large number of messages are sent, the network bandwidth will be exhausted to form another Denial-of-Service attack.3. The client can specify the IP address at will.The client does not have to use the DHCP service. It can set IP addresses in a static way. If any,This will greatly increase the possibility of network IP address conflict.II. Introduction to DHCP Snooping TechnologyDHCP Snooping is a DHCP security feature. Cisco s

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r

with option 82 from the L2 switch and establish binding entries for the information . 　　Of course, if you encounter the switch does not support IP DHCP snooping information option allow-untrusted command can have the following two solutions:① using the IP DHCP relay information trusted(in-VLAN) command within an int VLAN of an unsupported switch② on the access l

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL

templateHOST_NAME h17_2960sw1_3.251Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}Define Service{Use GENERIC-SERVICE,SRV-PNP; Inherit values from a templateHOST_NAME h18_2960sw1_3.247Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}6. Configure permissions (pending validation)[Email protected] ~]# chmod 777/var/tmp/check_traffic_10.10.3.249_10128.hist_dat_root__647. Restart the Nagios service[E

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch# Clear License All4. Disable and enable Telnet and SSHswitch# Config TSwitch (config) # no Telnet server enableSwitch (config) # Telnet Server enableswitch# Config TSwitch (config) # SSH server enableSwitch (config) # no SSH server ena

Cisco LAN switches are still commonly used. So I studied the maintenance and configuration problems of Cisco LAN switches. I would like to share them with you here, hoping to help you. Cisco LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's ipvst5000 series Cisco