Alibabacloud.com offers a wide variety of articles about cisco 3850 configuration guide, easily find your cisco 3850 configuration guide information here online.
communicate router (config-if) #no shutdown //Open port Router (config) #^zrouter#showr Router0 Static routing configuration router>enablerouter#conf Trouter (config) #ip Route 192.168.2.0 255.255.255.0 10.254.10.2 (Command interpretation: When the destination network address is 192.168.2.0, forward to port address 10.254.10.2 routes) Router (config) #^zrouter#show IP routeRouter1 Static routing configuration
communicate router (config-if) #no shutdown //Open port Router (config) #^zrouter#showr router0 Dynamic routing configuration Router>enablerouter#conftrouter (config) # routerrip //enable RIP dynamic routing protocol Router (config-router) #version 2 //using version 2, RIPV2 protocol router (config-router) # NETWORKNBSP;192.168.1.0NBSP;NBSP;NBSP;NBSP;NBSP;//Specifies the network that needs to be advertised (at the router interface) Router (config-rou
: interface fastethernet0/1s2960 (config-if) #speed 100s2960 (config-if) #duplex fulls2960 (config-if) # end//at the same time the PC0 network card to full duplex mode, 100M rate, otherwise the link is not through s2960#showinterface //Display Port All information s2960#show mac-address-tables2960#configts2960 (config) #line console0 //Entering console line mode S2960 (config-line) #password cisco //Set the login password for the console line S2960 (c
is of type Rstpswitch (config) #endSwitch #showspanning-tree nbsp//determine root switch, port role, port status, etc. # Link Test PC0 (Command prompt cmd) ping 192.168.1.4//link switch0switch>enswitch#conf tswitch (config) #inter f0/23 Turn off Port switch (config-if) #shutdownPC0 (Command prompt cmd) on the main link ping 192.168.1.4//link//Backup link flag changed from yellow to green, indicating backup link is enabled Lab Environment: Windows 7, C
[CISCO] NAT configuration full guide vronat NAT Function configuration introduction with the rapid development of the internet, the shortage of IP addresses has become a very prominent problem. A variety of solutions have emerged to solve this problem. The following describes an effective method in the current network
(VLAN) #exitSwitch #showvtp status//viewing VTP configuration information switch#show vlanbrief// Display VLAN configuration information switch#conftswitch (config) #inter f0/1switch (config-if) #switchport accessvlan The 2//divides the port into Vlan2switch (config-if) #exitSwitch (config ) #inter f0/2switch (config-if) #switchport NBSP;ACCessvlan3//divide the port into Vlan3switch (config-if) # Exitswitc
) #port-channelload-balancedst-ip//to achieve load balancing by Destination IP address switch ( Config) #exSwitch #showetherchannelsummary NBSP;NBSP;NBSP;NBSP;//Display Ethernet Channel Information Switch#conftswitch (config) #interface port-channel1 //port configuration mode switch (config) into the aggregation port #exSwitch #showinterfacesetherchannel //displaying aggregation port information PC0 (Command prompt cmd) ping 192.168.1.3//link ping 19
//Set the host name s2960s2960 (config) #interface fastethernet0/ 1//Enter configuration mode S2960 (config-if) #exit //return to previous level mode S2960 (config) #ip address192.168.1.1255.255.255.0 //Set Switch IPS2960 (config) #ip default-gateway192.168.1.254//Set the default gateway S2960 ( Config) #ip domain-namecisco.com //Set the domain name S2960 (config) #ip name-server200.0.0.1 //Setting the domain name server S2960 (config) #no ip domai
) #port-channelload-balancedst-ip//to achieve load balancing by Destination IP address switch ( Config) #exSwitch #showetherchannelsummary NBSP;NBSP;NBSP;NBSP;//Display Ethernet Channel Information Switch#conftswitch (config) #interface port-channel1 //port configuration mode switch (config) into the aggregation port #exSwitch #showinterfacesetherchannel //displaying aggregation port information PC0 (Command prompt cmd) ping 192.168.1.3//link ping 19
3.12 layer-3 Switching Purpose: 1. master the basic configurations of layer-3 switching for inter-VLAN communication. 2. Understand the implementation principle of layer-3 switching. Tutorial topology: 650) this. width = 650; "src =" http://www.bkjia.com/uploads/allimg/131227/062203O08-0.png "title =" 3.12.png "/> Tutorial steps: 1. Deploy the Trunk link between SW1 and SW2 Based on the topology shown in the figure. The configuration is as follows:
refresh the cache to find650) this.width=650; "Style=" background-image:none;padding-left:0px;padding-right:0px;border-top-width:0px; border-bottom-width:0px;border-left-width:0px;padding-top:0px; "title=" lip_image029_thumb3 "border=" 0 "alt=" lip_ Image029_thumb3 "src=" Http://s3.51cto.com/wyfs02/M00/7D/C2/wKioL1bvmTWgM9FxAAHXmre7Xd0988.gif "width=" 579 "Height = "260"/>Limited number of words, follow-up information please see the next articleWindows.server.2008.r2.active.directory.
Start building with 50+ products and up to 12 months usage for Elastic Compute Service
1 on 1 presale consultation
24/7 Technical Support 6 Free Tickets per Quarter Faster Response
Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.
A comprehensive suite of global cloud computing services to power your business
Payment Methods We Support
