cisco 3900 switch

There was just one Cisco 2960 switch that failed this afternoon, replacing an alternate switch immediately, but the backup switch was transferred back from another branch and the password was forgotten. Just use the recovery password process, also share it.1. Set the Windows HyperTerminal, name customization. Recommend

Tags: Cisco switchBasic configuration and management of switches• Technical Principles• The switch is managed in two basic ways: in-band management and out-of-band management.• The console port management switch through the switch is out-of-band management, which does not occupy the network port of the

) #interface range F0/1-2 (check 1.2 port number)Switch (config-if-range) #switchport Access VLAN 3 (Connect 1.2 ports to VLAN3)Interface joins VLAN:Switch (config) #interface fastethernet 0/1 (enter Port 1th)Switch (config-if) #switchport Access VLAN 2 (Configure the 1th interface into vlan2)Trunk Trunk Link:Implement VLAN communication across switchesTrunk links can host multiple VLANsIdentity of the VLAN

with option 82 from the L2 switch and establish binding entries for the information . 　　Of course, if you encounter the switch does not support IP DHCP snooping information option allow-untrusted command can have the following two solutions:① using the IP DHCP relay information trusted(in-VLAN) command within an int VLAN of an unsupported switch② on the access l

With the development of China's routing industry, we have also promoted the update and upgrade of the routing switch technology. Here we have introduced the IOS restoration method of the Cisco routing switch, and we have tried one method, after Flash is deleted, the system cannot be started. You can use X-Modem to restore it. At that time, I accidentally deleted

Experimental topology Router (config) #frame-relay switching to simulate a router as a Frame relay switch Router (config) #inter S1/1 Router (config-if) #clock rate 128000 Router (config-if) #encapsulation Frame-relay Configuration Interface encapsulation and binding relay The default Frame relay enabled on the interface is encapsulated in the Cisco package and, if connected to a non-

High intelligence, high availability, and high reliability are the characteristics of multi-layer intelligent optical fiber switch. Although its technology is not very mature yet, it has been recognized by people. Cisco Systems recently announced that it will launch the CiscoMDS9100 series of multi-layer smart Optical Fiber switches this fall to meet the needs of small and medium-sized enterprises for deplo

The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of ports and enter the port batch configuration view Figure#switchport mode truck will figure p

Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771)Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771) Release date:Updated on:Affected Systems: Cisco catalytic 6500 Description: Bugtraq id: 75063CVE (CAN) ID:

Cisco switch password settings www.2cto.com 1. set console password> enable # configure trminal (confing) # line console 0 secure console port ① (config-line) # password (cisco) Secure password (config-line) # login logs must not be small. console Password settings complete exit 2: set the global password www.2cto.com enadle # configure terminal ② (config) # enab

Topology map: 1. Configure the router R4 as a Frame relay switch Frame-relay switching * configured as Frame Relay switch 2. Configure the interface's clock frequency, package type, LMI type and Frame Relay DCE on the router R4 int s0/0 No shut Clock rate 64000 * Set clock frequency Encapsulation Frame-relay * Encapsulated as Frame Relay Frame-relay lmi-type

Overview of LAN switches LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's Catalyst 5000 Series LAN switch as an example. It includes an integrated switching hardware structure, 10-Mbps Ethernet that supports switching, and-Mbps Fast Ethernet, supports fast Ethernet, FDDI, exchange-type ring, and layer-3 switching processing. This type of switch

Welcome to the network technology community forum, and interact with 2 million technical staff to enter the settings and skills of the two CISCO switches, mainly: Cisco switch setup skills to find the MAC address corresponding to the IP address, cisco switch setup tips: Find

This tutorial describes how to start and configure Cisco Catalyst 1900 series switches.1. Tutorial PurposeThrough this experiment, you can master the following skills:Familiar with switch startup interface;Configure the vswitch;Understand the port number of the vswitch.2. device requirementsThis experiment requires the following devices:One Cisco Catalyst 1900 Se

1. Unplug the power cord of the vswitch, press the switch Mode button, and re-plug the power cord of the vswitch. Release the Mode button after the LEDs on Port 1x are off. 2. For the Catalyst 2940/2950 L series: Unplug the power cord of the switch, hold down the Mode button of the switch, and re-plug the power cord of the sw