cisco 4300 router

1. Preparation Tools Cisco TFTP server, HyperTerminal, iOS files iOS files are not easy to find, you need to look at the hardware version, as well as the size of ROM RAM, to my Cisco 2621XM for example (with two fastethernet),Start looking for a few 2600 of iOS, the brush is not correct, the problem of unrecognized network interface, can not be configured, there should be F interface with S Ios,

CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access. Task commands Set the PPP encapsulation ppp1 Set the authentication method ppp authentication {chap | chap pap | pap cha

This article describes how to control the BT traffic of a Cisco router through specific operations, and describes the specific operation methods in detail. I hope this article will help you. Network-Based Application Recognition (NBAR) indicates Network Application Recognition. NBAR is a technology that can dynamically search for protocols in Layer 4 to Layer 7. It can not only control static and simple net

are used The route of this packet. ---- GRE only provides encapsulation of data packets. It does not have encryption to prevent network listening and attacks. Therefore, in the actual environment, it often corresponds to an IP address. When the SEC is used together, IPSec provides encryption of user data to provide users with better security. The GRE protocol has two main purposes: internal protocol encapsulation and private address encapsulation. In China, CEN uses almost all TCP/IP protocols,

Probably a lot of people on the Cisco router speed limit is not a special understanding, so I studied the Cisco router speed limit detailed settings statement, here to share with you, I hope to be useful. In a Cisco router device,

CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one

This article describes how to enhance the security of a Cisco router by using a Nipper. So how should we use it? The following article gives you a detailed answer. How do I use a Nipper? Since Nipper supports so many devices and is also known to support a wide range of multi-functional options, it is impossible for me to present them in all aspects. However, we can make a basic demonstration. In our example

One. Test the topology:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/CA/wKiom1WH46fhBjvJAADX2zoss3k937.jpg "title=" TP1. JPG "alt=" Wkiom1wh46fhbjvjaadx2zoss3k937.jpg "/>Two. Test ideas:A. Enable resolution by IP NAT without setting the direction---this way can be accessed directly from the public IP address, or can be accessed by domain name method---unfortunately Cisco is different iOS, some although have IP nat enable, but do not re

Necessity for configuring WRED on a Cisco Router Although the queue provides VoIP QoS congestion management, it still needs some congestion avoidance mechanisms, such as WRED. In particular, WRED can prevent the output queue from reaching the limit value, which will lead to the loss of all input packets. This article comes from Informit and discusses the necessity of configuring WRED on a

255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all

Cisco routers are widely used in network interconnection. Among them, 2500 series routers are widely used in low-end users. So what if you accidentally forget the superuser password of the 2500 series router? Don't be afraid, as long as you can restore as follows:Preparation: a computer running Terminal simulation program can start a Super Terminal in Windows 95/98), and the microcomputer serial port COM1/C

Cisco once again launched a new generation of router products and also applied new technologies. So I studied how Cisco developed the new VQE technology to solve the problem of IPTV Video Delivery. Here I will share it with you, I hope it will be useful to you. Cisco has announced the release of the VisualQualityExperi

Cisco IOS is a dedicated kernel that provides routing, switching, network interconnection, and remote communication capabilities. Most Cisco routers are running iOS, and more and more Cisco Catalyst switches are running it, including Catalyst2960 and Catalyst3560 series switches. Some important aspects of the Cisco

The Cisco router NAC solves the problem. The so-called NAC is an architecture that allows multiple hardware and software components to work together to protect the user's network from adverse client attacks. 1. It is not easy to fully implement NAC, because the entire architecture contains too many different components from other vendors. For example, the architecture contains the NAC Policy Manager and mul

Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685)Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685) Release date:Updated on:Affected Systems: Cisco ASR 1000 Description: CVE (CAN) ID: CVE-2015-0685The

In Cisco router configurations, NAT configurations are frequently used. I hope the introduction below will be helpful to the majority of fans. It is a common method. The vro performs simple NAT translation and sets a CIDR Block in the NAT address pool. After a while, I found that the address pool was a waste of time. When I wanted to use a real ip address, I couldn't use it, so I decided to modify the

Use the tftp function of Linux to configure information about cisco router-Linux Enterprise Application-Linux server application. The following is a detailed description. In a LAN environment, if there are Cisco routers and Linux servers. Maybe you need to use Linux The TFTP service downloads the Cisco

One. Test the topology:Two. Test ideas:Three. Basic configuration:A.R1:Interface ethernet0/0IP address 202.100.1.1 255.255.255.0No shutdownIP Route 0.0.0.0 0.0.0.0 202.100.1.2B.R2:1. Interface configuration:Interface ethernet0/0IP address 202.100.1.2 255.255.255.0No shutdownInterface ETHERNET0/1No IP addressNo shutdown2.PPPOE Server configuration:AAA New-modelAAA Authentication PPP Default LocalUsername Cisco password 0

:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interface mode, and configure the Ip-> activation in