cisco 4300 router

First, the experimental topologySecond, the specific configurationRouter (config) #do sh runbuilding configuration ... Current configuration:604 bytes!version 12.4no service Timestamps log datetime MSECNO service timestamps debug datetime MSECNO Service Password-encryption!hostname router!ip dhcp excluded-address 192.168.1.1!IP DHCP Pool ABCNetwork 192.168.1.0 255.255.255.0Default-router 192.168.1.1Dns-serv

that needs to be mapped to the Internet for access by others. 650) this. width = 650; "border =" 0 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/02223S615-0.jpg "/> The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step

Cisco router reset enable password tutorial, ciscoenable Steps: 1. Restart the vro and press ctrl + Breack when ROM Monitor mode appears on the vro to enter ROM mode, for example: 2. Modify the vro register value, change the original register value 0x2102 to 0x2124, and then run the reset command to restart the device, for example: 3. After the password is changed, the value of the drop register in

How to Set Up r12002 routing protocol for Cisco router 3620 to demonstrate how to set up r12002 routing protocol for Cisco router 3620 this time, we need to build a complex network experimental environment, this environment is also the experimental environment used later to learn about other

This test configures remote management of routers and switches within the LAN, routers for Cisco 2621XM, switches for Cisco 2960Switch configuration:Switch>enaSwitch#confSwitch#configure TSwitch (config) #interface vlan 1Switch (config-if) #ip address 192.168.2.10 255.255.255.0Switch (config-if) #exitSwitch (config) #ip Default-gateway 192.168.2.100Switch (config) #enable secret 123Switch (config) #line vty

First, the Cisco router to introduce the memory A router is similar to a computer in that it also has memory, operating system, configuration, and user interface, and the operating system in Cisco routers is calledInternet Operating System (Internetwork operating system) or iOS. The following is mainly about the stora

customized within a Network as needed without application. In the network, computers communicate through internal IP addresses. When the internal computer needs to communicate with the external internet, the device with the NAT Function (such as a router) converts an internal IP address to a valid IP address (that is, the requested IP address) for communication. 　　 2. NAT application environment 　　　　 Scenario 1: an enterprise does not want external n

Update the public ip address of the Cisco router. First, confirm how your network is going. Here we will talk about the configuration based on our network: first, remove the default route no ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx adds the new default route www.2cto.com ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx then remove the ACL to overwrite the no ip nat inside source list 1 pool BJ. RK overload re

Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host

There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2

When we use Telnet to log on to the device, the user name and password are transmitted in clear text, in order to ensure the security of the data, we recommend the use of SSH login device. The following is the configuration of the Cisco router SSH:1. Configuring hostname and Domain-nameR1 (config) #hostname R1R1 (config) #ip domain-name frame.com2. Generate the key, here is the 1024-bit key, the key length

The port Mapping method enables access to specific port services from the Internet to the local area network internal machines. For example, the machine you are using is in a LAN connected to the Internet, all the services you open on the machine (such as FTP), by default, the outside world can not access. This is because your IP is the LAN internal IP, and the outside can access only the server you are connected to the IP, because the entire LAN on the Internet only a real IP address, and this