cisco 5500 switch

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL

templateHOST_NAME h17_2960sw1_3.251Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}Define Service{Use GENERIC-SERVICE,SRV-PNP; Inherit values from a templateHOST_NAME h18_2960sw1_3.247Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}6. Configure permissions (pending validation)[Email protected] ~]# chmod 777/var/tmp/check_traffic_10.10.3.249_10128.hist_dat_root__647. Restart the Nagios service[E

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch# Clear License All4. Disable and enable Telnet and SSHswitch# Config TSwitch (config) # no Telnet server enableSwitch (config) # Telnet Server enableswitch# Config TSwitch (config) # SSH server enableSwitch (config) # no SSH server ena

Cisco 3750 switch stack configuration points 3750 stack is a real stack, the Catalyst 3550 series uses StackWise technology, it is an innovative stack architecture, A 32 Gbps stack interconnection is provided to connect up to nine switches and integrate them into a unified, logical, and optimized device for convergence, in this way, customers can deploy voice, video, and data applications with greater confi

In many cases, we may need to log on to the Cisco switch to execute some common viewing commands, but it is troublesome to run cmd, enter the password, and enter the command. The discovery can be achieved through batch processing, as shown in figureLog on to the Cisco switch 192.168.0.1 and Ping another

We have explained a lot about the configurations of CISCO switches. Here we will mainly explain the port security configurations of CISCO 3550 switches. Scenario: There is a CISCO3550 switch in a certain unit. For the sake of network security, the security requirements for some ports are high, that is, only the specified host can be connected, for example, if you

Microsoft's Windows Server 2012 has been able to support LACP link aggregation, due to the use of link aggregation can achieve line redundancy and bandwidth increase, here I used a Cisco 2960 to do a test for interested friends reference.Experiment Preparation:Cisco switch 29,601, install server 2012 servers, there are two Gigabit network card, network cable two root.Steps:1. Configuration of

Simply record that a Cisco router is simulated as a frame relay switch, and the router must have a serial interface module. Liehuo.net // Enable Frame Relay switching on the vroFRSW (config) # frame-relay switching strong-fire-network // Enter the Interface Configuration ModeFRSW (config) # int serial 0/1 Veryhuo.com // Delete the interface IP AddressFRSW (config-if) # no ip address veryhuo.com // Co

The great god of you;I now have a Cisco boot from the 507R-E switch to report the following errors please advise.Checking the partition table and boot sector ...Checking FAT, Files and directories ...Reclaiming unused space ...Updating FAT ...Rom Monitor Program Version 12.2 (44R) SG5CPU rev:2.1, Board rev:8, Board type:103, CPLD nexu Rev:9Chassis:ws-c4507r-eFront Panel Phy is bcm5482sGot Mac ADDRESS:00:25:

It may take 30 seconds or more to connect a computer to a vswitch before the computer can communicate over the network. If you are waiting for a long time, 30 seconds of waiting will make you feel very long. Let's take a look at how to accelerate the port initialization process of the switch.Understanding the process of vswitch port InitializationWhen a device is connected to the port of a started switch, the swit