cisco answers

Using Cisco to build an experimental environment I.. Configure DHCP client;Two, configure the switch SW1SW1 (config) #vlan 10SW1 (Config-vlan) #exSW1 (config) #vlan 20SW1 (Config-vlan) #exSW1 (config) #int FA0/1SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 10SW1 (config-if) #no shutdownSW1 (config) #int FA0/2SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 20SW1 (config-if) #eSW1 (config

, 6800IA is restarting, patiently wait, and then observe.Router#show FexFex Fex Fex FexNumber Description State Model Serial---------------------------------------------------------------------------101 6800ia-48-01 Online c6800ia-48td foc2016s1ndAfter a wait, when you find that the status is online, that the 6800IA is connected to normal, you can configure it!We can see if the interface of IA is added by the show Run command.Router#show Run........................ Also omit the N-line configura

that the admin domain is able to overwrite all branch switches. The Cisco switch is capable of supporting any media as a trunk, and it can use its own ISL tags for relaying. ISL (Inter-Switch link) is a protocol between switches, between switches and routers, and between switches and servers to transfer multiple VLAN information and VLAN data streams, configured with ISL encapsulation via ports directly connected to the switch, The VLAN allocation a

(global configuration mode)S1 (config) #interface vlan 1 --Enter VLAN 1 PortS1 (config-if) #ip address 192.168.1.1 255.255.255.0 --Configure the vlan1 with an IP address so PC1 and S1 can ping interoperabilityS1 (config-if) #no shutdown --activating VLAN 1 PortS1 (config-if) #end --Return to privileged modes1#copy running-config startup-config --Save configuration (from memory RAM to hard disk NVRAM)s1#show running-config --View switch configuration4. Go to PC1 host command line interface(1) F

protocol between as is called the External Gateway Protocol External Gateway Protocol (also called Inter-Domain routing protocol): there are two types of inter-domain routing protocols: externalGateway Protocol (EGP) and Border Gateway Protocol (BGP)2) Dynamic routing according to the algorithm can be divided into: Distance vector routing protocol, link state routing protocolDistance Vector Routing protocol: Select Route RIP,IGRP based on the number of routes that are routed from the source net

Tags: HSRP working principle STP effect ACL access control List loop storm Cisco private protocolDay 031. What is HSRP? How does it work?HSRP: Hot Standby Routing protocolHSRP is a Cisco private protocol that ensures that user communication can be quickly and transparently restored when a network edge device or access link fails.This provides redundant rows for the IP network. By using the same virtual IP a

"Introduction" Within a switched network, it is possible to segment and organize flexibly through VLANs. VLANs can group devices in a LAN. A group of devices in a VLAN communicates as if it were connected to the same line. VLANs are based on logical connections, not physical connections. Types of VLANsThere are many different types of VLANs used in modern networks. Some VLAN types are defined by traffic category. Some other VLAN types are defined by specific features.Data VLAN: used to deliver u

Automatic backup and fallback of Cisco iOS profiles requires the use of the Archive Archive configuration mode feature of iOS. In general, only the version number of iOS has the Archive configuration mode feature in 12.3 (4) Cisco iOS profile automatic backup All commands are as follows: router> Router>enable Router#configure Terminal Router (config) #archive Router (config-archive) #write-memory

Trunk Link Trunk: Same inter-VLAN communication on different switchesHow to play tag tag encapsulationPackage Type: IEEE 802.1q/cisco ISLIEEE 802.1q:4 Bytes, internal encapsulation, publicCisco isl:30 bytes External encapsulation, privateSwitch port configuration mode: Trunk/acces (OFF)/Dynamic desirable/dynamic AutoTwo auto NO mode of operation generally either trunk or accessEthernet Channel: Multiple physical ports to form a logical port for greate

Some time ago, my colleague asked me a question about the DHCP configuration of the Cisco router. At that time, I did not give a positive answer, because this was my first time. In the following days, I have consulted relevant materials and are satisfied with the following answers. Share it with you now! In addition, most people do not know about the computer and do not operate these operations. Therefore,

(HSRP)Direct Connect Ping PassTarena-r1 (config) #interface f0/0TARENA-R1 (config-if) #standby 1 IP 192.168.1.254TARENA-R1 (config-if) #standby 1 priority 200 PrioritiesTARENA-R1 (config-if) #standby 1 preempt preemptive rightTARENA-R1 (config-if) #standby 1 track F0/1 port trackingTarena-r2 (config) #interface f0/0TARENA-R2 (config-if) #standby 1 IP 192.168.1.254 act as IPTARENA-R2 (config-if) #standby 1 priority 195 PrioritiesTARENA-R2 (config-if) #standby 1 preempt preemptive rightTARENA-R2

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1

One of my customers has a VPN which I 'd like to access. they provided me with a copy of the Cisco VPN Client for Linux, and a "PCF" configuration file for the client. here's what I had to do to get the Cisco VPN Client working in Linux-and it does work just fine. First we make a directory to put the bits and bobs in alan@hactar:~$ mkdir ciscoalan@hactar:~$ cd cisco