cisco e3000 router

that needs to be mapped to the Internet for access by others. 650) this. width = 650; "border =" 0 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/02223S615-0.jpg "/> The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step

Cisco router reset enable password tutorial, ciscoenable Steps: 1. Restart the vro and press ctrl + Breack when ROM Monitor mode appears on the vro to enter ROM mode, for example: 2. Modify the vro register value, change the original register value 0x2102 to 0x2124, and then run the reset command to restart the device, for example: 3. After the password is changed, the value of the drop register in

At present, China's wireless router industry is developing very rapidly, and its market demand is also very high. Here we mainly introduce Cisco's first dual-band wireless router launched in China, this section describes the features and performance of the vro. In May 19, Cisco launched the Linksys by Cisco dual-band w

The first of these methods This approach restores the following routers: Cisco 2000 series, 2500 series, 3000 series, Cisco 4000 series using the 680x0 Motorola CPU, and 10.0 series routers running 7000 versions of Cisco IOS systems. Implementation steps: 1. Connect a terminal at the console port of the router or a

Initial installation of the CISCO router tutorial During the first installation, the system automatically enters the Dialog Setup, as prompted on the screen, answer the router name, encrypted super login password, super login password, remote login password, dynamic routing protocol, and the configuration of each interface, and save the configuration. After the v

Telnet remote Login Configuration 1, configure Cisco router login account, password, account level, as shown below, account name ABC, password for abc123, account level of 15 (highest level) R1#configure Terminal R1 (config) #username ABC privilege secret abc123 R1 (config) #end r1# 2, configure the Cisco router

customized within a Network as needed without application. In the network, computers communicate through internal IP addresses. When the internal computer needs to communicate with the external internet, the device with the NAT Function (such as a router) converts an internal IP address to a valid IP address (that is, the requested IP address) for communication. 　　 2. NAT application environment 　　　　 Scenario 1: an enterprise does not want external n

Update the public ip address of the Cisco router. First, confirm how your network is going. Here we will talk about the configuration based on our network: first, remove the default route no ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx adds the new default route www.2cto.com ip route 0.0.0.0 0.0.0.0 xxx. xxx. xxx. xxx then remove the ACL to overwrite the no ip nat inside source list 1 pool BJ. RK overload re

Cisco router nat translation 1. One-to-one correspondence between the internal address and the egress address disadvantages: When the egress address resources are scarce, only a small number of hosts can be connected to the internet. 2. The internal address shares the egress address. The router uses the egress address and port number, as well as the external host

There are too many Qos information on the Cisco Router Traffic Control instance, but many of them are not practical. I have talked about a lot of theories. The following are the configurations on the routers of a subsidiary for your reference. In fact, as long as you understand the meaning of NBAR, CBWFQ, and WRED, traffic control can be configured as needed. Www.2cto.com Description: A subsidiary uses a 2

When we use Telnet to log on to the device, the user name and password are transmitted in clear text, in order to ensure the security of the data, we recommend the use of SSH login device. The following is the configuration of the Cisco router SSH:1. Configuring hostname and Domain-nameR1 (config) #hostname R1R1 (config) #ip domain-name frame.com2. Generate the key, here is the 1024-bit key, the key length

The port Mapping method enables access to specific port services from the Internet to the local area network internal machines. For example, the machine you are using is in a LAN connected to the Internet, all the services you open on the machine (such as FTP), by default, the outside world can not access. This is because your IP is the LAN internal IP, and the outside can access only the server you are connected to the IP, because the entire LAN on the Internet only a real IP address, and this

Cisco 7609 Router boot rommon modeCisco7609 boot into Rommon 1 > Mode solution:Rommon 2 > Dir disk0: Check if the file existsInitializing ATA Monitor Library ...Directory of Disk0:2 120962020-rw-c7600s72033-advipservices-mz.122-33.src3.binRommon 3 > Confreg 0x2102 Correcting register valuesRommon 7 > Boot=disk0:c7600s72033-advipservices-mz.122-33.src3.binRommon 8 > Sync SaveRommon 9 > I restartThe above ope

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one

255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all

Cisco routers are widely used in network interconnection. Among them, 2500 series routers are widely used in low-end users. So what if you accidentally forget the superuser password of the 2500 series router? Don't be afraid, as long as you can restore as follows:Preparation: a computer running Terminal simulation program can start a Super Terminal in Windows 95/98), and the microcomputer serial port COM1/C

The Cisco router NAC solves the problem. The so-called NAC is an architecture that allows multiple hardware and software components to work together to protect the user's network from adverse client attacks. 1. It is not easy to fully implement NAC, because the entire architecture contains too many different components from other vendors. For example, the architecture contains the NAC Policy Manager and mul

:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interface mode, and configure the Ip-> activation in

Cisco router Tcl script backdoor 2nd tests Author: Vic The security of Cisco routers is certain. Password verification is required for remote login. The Cisco passwords are encrypted in the following ways:1 not encrypted, plaintext display 650) this. width = 650; "border =" 0 "alt =" "src =" http://img1.51cto.com/attac