cisco ethernet switch

When switching data frames, a switch can select different modes to meet network and user needs. Cisco switches provide three switching modes: Storage forwarding Mode The Store-and-forward mode means that the switch can complete the entire data frame and perform the forwarding operation only after the CRC verification is passed. If CRC verification fails, that

Use a cisco router to simulate how to configure a frame relay switch (configure 3640 as a frame relay switch): 3640 (config) # frame-relay switching ---------------------- enable the frame relay switching function of the router 3640 (config) # int s0/0 ------------------------------------- enter the s0/0 interface 3640 (config-if) # no ip add --------------------

interruptRommon 1 > "Interrupt"2.2go in Rommon mode start using the command configuration as follows Step:Rommon 1 > Confreg Choose y or N below the word bad I'll tell Y or N in the order of choice. Excuse me. The order is as follows: 1. Y 2.N 3.N 4.N 5.N 6.N 7.Y 8.N 9.N 10.N650) this.width=650; "style=" Float:none; "title=" 123.png "src=" http://s3.51cto.com/wyfs02/M02/71/37/ Wkiom1xjr8dtoehaaagcy3dy9aw290.jpg "alt=" Wkiom1xjr8dtoehaaagcy3dy9aw290.jpg "/>650) this.width=650; "style=" Float:non

Upgrade object: WS-C3750-24TS-E Ingredients: Cisco TFTP server, one cable (connecting hosts and switches), my ThinkPad Local Area Connection: 2.2.2.1 3750-vlan 1:2.2.2.2 Telnet to the switch for configuration 1. Setting up a TFTP server Close other network connections on the host to ensure that the TFTP server address is a locally attached IP (2.2.2.1). Copy the new iOS to the TFTP server root directory.

Configuration of a layer-3 Cisco switch 1. Start a route on a layer-3 switch. Otherwise, layer-3 switch does not have the routing function switch (config) # ip routing2. Configure the VLAN ip address switch (config) # interface vl

Cisco 3750 switch stack configuration points 3750 stack is a real stack, the Catalyst 3550 series uses StackWise technology, it is an innovative stack architecture, A 32 Gbps stack interconnection is provided to connect up to nine switches and integrate them into a unified, logical, and optimized device for convergence, in this way, customers can deploy voice, video, and data applications with greater confi

The Cisco router switch sets automatic backup for IOS files and restores the automatic backup and rollback of Cisco IOS configuration files. The archive configuration mode function of IOS is required. Generally, only IOS versions 12.3 (4) All commands for automatic backup of the Cisco IOS configuration file are as foll

In many cases, we may need to log on to the Cisco switch to execute some common viewing commands, but it is troublesome to run cmd, enter the password, and enter the command. The discovery can be achieved through batch processing, as shown in figureLog on to the Cisco switch 192.168.0.1 and Ping another

How to view the configuration of a Cisco switch interface, the following small set of specific operations 1, first Cisco switch boot, computer connection, enter the user mode, as shown in the picture: 2, enter "Enable" or "en", into the privileged mode, as shown in the figure: 3,

Tags: cisco/remote configurationIn actual work our routing and switches are always placed in the room to facilitate our work we need to configure the routing and switches so that we can configure the routers and switches in the office or at home.This is a simple network topology diagram where a computer-connected route configures the switch across network segmentsFirst we determine the PC ip:192.168.1.1 255

message are correctIf a large number of messages are sent, the network bandwidth will be exhausted to form another Denial-of-Service attack.3. The client can specify the IP address at will.The client does not have to use the DHCP service. It can set IP addresses in a static way. If any,This will greatly increase the possibility of network IP address conflict.II. Introduction to DHCP Snooping TechnologyDHCP Snooping is a DHCP security feature. Cisco s

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r

) # Policy-map Rate-limit-uplink//define uplink rate of 30M Switch (CONFIG-PMAP) # class Rate-limit-uplink Switch (config-pmap-c) # Trust DSCP Switch (config-pmap-c) # police 30000000 1000000 exceed-action drop//30M cannot be written 30720000 Otherwise, the following error will be reported:%error:policer rate should be multiples of 1000000. Please choose eit

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL