cisco industrial ethernet switch

1). Configure the VLAN Port Number of the switch named Switch1 as follows: Switch1(config)#int e0/2Switch1(config-if)#vlan-membership static 2Switch1(config-if)#int e0/3Switch1(config-if)#vlan-membership static 2Switch1(config-if)#int e0/4Switch1(config-if)#vlan-membership static 2……Switch1(config-if)#int e0/20Switch(config-if)#vlan-membership static 3Switch1(config-if)#int e0/21Switch1(config-if)#vlan-membership static 3Switch1(config-if)#

A rstp fault Early in the morning, I received a call and the ping gateway to the direct connection failed. No interface arp table for dis ARP Dis mac-address without related interfaces It seems that there are only physical problems, but it is said that interfaces and cables are okay. View dis stp interface Ethernet 1/0/1 ---- [CIST] [Port1 (Ethernet1/0/1)] [DISCARDING] ---- Port Protocol: enabled Port Role: CIST Designated Port Port Priority: 128 Port

Cisco's VLAN implementations are typically port-centric. The port connected to the node will determine the VLAN on which it resides. There are two ways to assign a port to a VLAN, which is static and dynamic, respectively. The process of forming a static VLAN is the process of assigning a port to a VLAN in a mandatory manner. That is, we first set up the VLAN on the VTP (VLAN trunking Protocol) server, and then assign each port to the corresponding VLAN process. This is the most common method we

numbers to this value. Each vswitch has a baseline MAC Address. Run the following command to see Sw2 # show versionBase ethernet MAC Address: 00: each port of the 0D: 28: 61: 35: 00 switch has a MAC address, which is obtained by adding the port number to the Base (baseline) MAC address. Show interfacef0/1 this command can see the MAC address of the switch port t

Encapsulation Frame-relay boot Frame Relay Package Encapsulation Novell-ether rules the Novell unique format used on the network segment Encapsulation PPP set PPP to the encapsulation method used by the serial port or ISDN interface Encapsulation SAP rules the Ethernet 802.2 format used on the network segment the Cisco password is SAP End Exit Configuration mode Erase Remove flash memory or configure

protected] bonding] # ethtool EM2Settings for EM2:Supported ports: [TP]Supported link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullSupports auto-negotiation: YesAdvertised link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullAdvertised pause frame use: NoAdvertised auto-negotiation: YesSpeed: 1000 MB/SDuplex: fullPort: Twisted PairPhyad: 1Transceiver: InternalAuto-negotiation: OnMDI-X: UnknownSupports wake-on: GWake-on: dLink detect

(0.0.514), CISCO DEVELOPMENT TEST VERSION Compiled Fri 13−dec−02 17:38 by Madison Ws−c2955t−12 starting ... Base Ethernet MAC address:00:0b:be:b6:ee:00 Xmodem file system is available. Initializing Flash ... Flashfs[0]: Files, 2 directories Flashfs[0]: 0 Orphaned files, 0 orphaned directories FLASHFS[0]: Total bytes:7741440 Flashfs[0]: Bytes used:4510720 Flashfs[0]: Bytes available:3230720 Flas

No X2Input Flow-control is off, output Flow-control is offARP Type:arpa, ARP Timeout 04:00:00Last input never, output never, output hang neverLast clearing of "show interface" counters neverInput queue:0/2000/0/0 (size/max/drops/flushes); Total Output drops:0Queueing Strategy:fifoOutput Queue:0/40 (Size/max)5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets Input, 0 bytes, 0 no bufferReceived 0 broadcasts (0 multicasts)0 runts, 0 giants, 0 throt

For complete syntax and application information about this chapter, seeCatalyst 3550 Multilayer Switch Command ReferenceAnd Cisco IOS Interface Command Reference For Release 12.1. Understanding Interface Types This section describes different interface types and some reference content for configuring these interfaces in detail in other sections. Other sections describe the configuration process of physi