cisco ip sla configuration

remote login access. Routing configuration Mode Route (Config-router) # Router Routing protocol Configuration of the router-related routing protocol into Interface configuration mode Route (config-if) # Interface interface The interface configuration mode can

Cisco DHCP configuration has always been our focus. We have also sorted out some materials in this regard. The following is the specific content. A company uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4, And the L2 Switch uses two

Users using Cisco routing, many of them do not pay much attention to doing Cisco router configuration work, in fact this is a very important part, especially for our network security. There are several ways to do Cisco router configuration. The

the duplex setting on the Catalyst switch side.7500 (config-if) # full-duplex7500 (config-if) # exit! -- If using ISL trunking, configure two port-channel sub-interfaces and enable ISL trunking! -- By issuing the encapsulation isl Command. ! -- Configure IP addresses for InterVLAN routing. 7500 (config) # int port-channel 1.1 7500 (config-subif) # encapsulation isl 1 7500 (config-subif) # ip a

A Cisco router uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4, And the L2 Switch uses two Cisco 2950, A layer-3 Switch uses a Cisco 3550. There are two VLANs in the network. To simplify the descriptio

.png"/> Configuration Requirements: The interface IP addresses must be configured for different systems in Figure 1, and the dynamic routing protocol RIP must be enabled for different systems, it also requires that each IP node in the network environment can communicate with another IP address. Use ping to view the rou

think it should be similar to the Cisco router, and then use the configuration line from the computer's COM2 to the PIX 525 console port, into the PIX operating system using the "HyperTerminal" in Windows, the communication parameters are set to silent. Initial use has an initialization process, the main settings: Date (date), Time (times), hostname (host name), Inside

Router Access ADSL configuration detailed 1, Cisco router connection to the ADSL modem configuration: Note: The case for Beijing Telecom ADSL PPPoE access, need to use a common ADSL modem and a Cisco 2500 router (dual Ethernet port), IOS 12.2 (T), Be able to realize LAN sharing Internet. This case

Some time ago, my colleague asked me a question about the DHCP configuration of the Cisco router. At that time, I did not give a positive answer, because this was my first time. In the following days, I have consulted relevant materials and are satisfied with the following answers. Share it with you now! In addition, most people do not know about the computer and do not operate these operations. Therefore,

. Setting up TelnetTelnet has a version of the change. Before the PIX OS 5.0 (the version number of the PIX OS), the PIX can only be accessed via Telnet from hosts on the internal network. In PIX OS 5.0 and later versions, Telnet to PIX Access can be enabled on all interfaces. When you want to telnet to the PIX firewall from the external interface, the Telnet traffic needs to be protected with IPSec, which means that the user must configure the PIX to establish an IPSec tunnel to another pix, ro

IOS also supports VLAN configuration and management, IP address management, and secure network service access. Introduction to the Catalyst6000 Series The megast6000 family includes the megast6500 series and Catalyst 6000 series, providing a series of new high-performance multi-layer switching solutions for campus networks. The Catalyst 6000 family is designed to meet the increasing requirements for gigabi

configuration information.R1#copy Run star//Save the current configuration as a boot-time configuration, or write memoryR1#sh Runr1# Erase startup-config//Delete boot profile r1#reload//restart routeR1 (config) #banner MOTD #----------Configure the router so that a caption is displayed when the console port is loggedContent#---ExitR1 (config-if) #description "TO