cisco ip sla configuration

Configure the PPPoE configuration for connecting a CISCO router to an ADSLmodem through the PPPoE configuration: hostnamebjsite! Ipsubnet-zeronoipdomain-lookup! Vpdnenablenovpdnlogging! Vpdn-group1request-dialinprotocolpppoe! Interfaceethernet00ipaddh Configure PPPoE for connecting a CISCO router to an ADSL modem using

connections, use Access list to strictly control access to the address, you can use AAA to set User access control. 8,ios upgrades and backups, as well as backup of configuration files suggest using FTP instead of TFTP. Such as: Router (Config) #ip FTP username Blushin Router (Config) #ip ftp password 4tppa55w0rd Router#copy startup-config ftp: 9, timely up

CISCO PT Simulation Experiment (19) NAT feature configuration for routersExperimental Purpose :Mastering the principle and function of NAT network address translationMaster the configuration of static NAT to achieve LAN access to the InternetMastering the principle of wide area network (WAN) access technologyExperimental Background : in order to adapt to the comp

The following is the VOIP configuration of Cisco 3640. The structure is VOIP between Taipei and Shanghai, followed by Alcatel's PBX. There are many things to note. Taipei configuration code: Taipei # sh runBuilding configuration... Current configuration :! Version 12.0 serv

communications that do not yet have an IP address, it is obvious that you can only use Mac multicast, how to route the multicast traffic received by the network card to the application, cannot rely on the protocol stack routing, because at this time the IP layer is not pass, rely on what? Rely on packet sockets!Of course, the above discussion is a bit simple, there is no IGMP and pruning and so on, in fact

trunkSwitch (config-if) #switchport trunk allowed VLAN, set allowed VLANsSwitch (config-if) #switchport trunk encap dot1q; set VLAN trunkingSwitch (config) #vtp domain; Set the VTP domain nameSwitch (config) #vtp password; set the VTP passwordSwitch (config) #vtp mode server, setting the VTP patternSwitch (config) #vtp mode client, setting the VTP patternSwitch set IP address:Switch (config) #interface vlan 1; go to VLAN 1Switch (config-if) #

CISCO PT Simulation Experiment (14) router configuration for OSPF dynamic routingExperimental Purpose :Mastering the configuration method of OSPF dynamic route selection protocolMastering the OSPF route description in the routing tableFamiliar with the principle and process of routing and packet forwardingExperimental Background : The company connects to the egre

normal half 10 10 BaseT 4/2 inactive 2 normal half 10 10 BaseT 4/3 inactive 2 normal half 10 10 BaseT 4/4 notconnect 1 normal half 10 10 BaseT 4/5 inactive 2 normal half 10 10 BaseT 4/6 At this time, VLAN 2 and VLAN 20 are not activated, so the ports on VLAN 2 and VLAN 20 are inactive. -------------------------------------------------------------------------------- Set VLAN 20 If you have VTP server and VTP clent in the network, set VLAN 20 on The VTP server. Cat5001> (enable) set vlan 20 VLAN

line.Experimental topology :650) this.width=650; "Src=" https://s1.51cto.com/wyfs02/M01/9E/37/wKiom1mMq8bAYTQvAABChwodcMs817.png-wh_500x0-wm_ 3-wmp_4-s_3687498630.png "title=" 12.1.PNG "width=" 419 "height=" "" border= "0" hspace= "0" vspace= "0" style= "width : 419px;height:320px; "alt=" Wkiom1mmq8baytqvaabchwodcms817.png-wh_50 "/>Experimental steps:New Cisco PT topology diagramSet IP and gateway addresse

The Cisco 2511 router configuration method is used as a port device to connect to the WAN. The router has been widely used. Its main function is to connect multiple independent networks or subnets, achieve optimal path finding and data transmission between the Internet. This article takes the Cisco 2511 vro as an example to introduce four router

Tags: Cisco MDS zone san Configure a Cisco MDS Optical Fiber storage switch (MDS multilayer Director Switch multi-layer optical fiber array switch)General process: 1: Create a vsan, add the port to vsan2: create a zone, add the port to zone3: Create a zoneset, add the zone to the set, and enable zoneset4: Enable all ports Use command line basic configuration

Vswitches need to be configured for the recently merged server link set... I have never obtained a vswitch before. I want to sell it now... Generally, the vswitch supports telnet. If you have configured an ip address, you can directly telnet the vswitch. If you do not have any configuration, you need to use the Serial port. Choose Serial for the Serial port... Fortunately, we support all the omnipotent put

Cisco 2811 Routers Detailed configurationRouter>enableRouter#configure TerminalRouter (config) #hostname cisco2811//define router name2811 (config) #enable password 124563831//Set Login password2811 (config) #line vty 0 42811 (config-line) #password 124563831//Set Telnet password2811 (Config-line) #login2811 (Config-line) #exit2811 (config) #interface fastethernet 0/0//Set Intranet interface2811 (config-if) #ip