cisco l3 switch

gigabitethernet0/2Switch (config-if) # no switchportSwitch (config-if) # ip address 192.20.135.21 255.255.255.0Switch (config-if) # no shutdownSwitch (config-if) # endAppendix: show interfaces [interface-id] switchport // display the status of the L2 port, which can be used to determine whether the port is a L2 or L3 port. Eg: Switch # show interfaces fastethernet 0/1 switchport* VLAN settings on a layer-3

High intelligence, high availability, and high reliability are the characteristics of multi-layer intelligent optical fiber switch. Although its technology is not very mature yet, it has been recognized by people. Cisco Systems recently announced that it will launch the CiscoMDS9100 series of multi-layer smart Optical Fiber switches this fall to meet the needs of small and medium-sized enterprises for deplo

The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of ports and enter the port batch configuration view Figure#switchport mode truck will figure p

Cisco switch, Cisco switchesSwitch> enable Switch # con Switch # conf Switch # configure ter Switch # configure terminal Enter configuration commands, one per line. End with CNTL/Z.

Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771)Cisco Catalyst 6500 Series Switch Denial of Service Vulnerability (CVE-2015-0771) Release date:Updated on:Affected Systems: Cisco catalytic 6500 Description: Bugtraq id: 75063CVE (CAN) ID:

#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating

): can only receive or send bpdus messages learning (learning) : can receive or send BPDU Message, and form mac forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by default. The

) -------------------------------------------------------------------------------- Add Catalyst 5002 to the domain You need to add Catalyst 5002 To The VTP management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server. Note: by default, the Catalyst 5000 series switches are VTP servers. Cat5002> (enable) Cat5002> set vtp domain cisco mode client T

Cisco switch password settings www.2cto.com 1. set console password> enable # configure trminal (confing) # line console 0 secure console port ① (config-line) # password (cisco) Secure password (config-line) # login logs must not be small. console Password settings complete exit 2: set the global password www.2cto.com enadle # configure terminal ② (config) # enab

Tags: Cisco MDS zone san Configure a Cisco MDS Optical Fiber storage switch (MDS multilayer Director Switch multi-layer optical fiber array switch)General process: 1: Create a vsan, add the port to vsan2: create a zone, add the port to zone3: Create a zoneset, add the zon

Overview of LAN switches LAN switches have evolved from a HUB-based LAN shared in the traditional sense to a broader space. Take Cisco's Catalyst 5000 Series LAN switch as an example. It includes an integrated switching hardware structure, 10-Mbps Ethernet that supports switching, and-Mbps Fast Ethernet, supports fast Ethernet, FDDI, exchange-type ring, and layer-3 switching processing. This type of switch

Basic configuration and management of the Cisco PT Simulation Experiment (1) switchExperimental Purpose : Master the basic configuration and management of the switch, and understand the basic commands of the switch configuration. Experimental background : A company has a new batch of two-layer switch, before formally p

Recently, the OS of a vswitch is old, so I want to update it. I want to ask a user to update the OS. After updating the OS, the problem occurs, I have a password for the OS. Since the password is being used and it is difficult for them to ask for it, I am ready to clear the password. After finding the relevant article on www.cisco.com, cleared successfully. Write down the cleanup process. Let's talk about the configuration environment first, the switch