cisco router reboot command

"Data Collation" Cisco [Shell, Command]Promotmode{usermode:router> (input:enable) privilegemode:router# (input:conft) Globalconfigmode:router (Config) #----ctrl-z->pm,exit-> Gcminterface:router (config-if) #Sub-interface:router (config-subif) #Controller: Router (config-controller) #Line: Router (config-line) #

, configure the router to access other network segments required by the gateway18. Show the status of each line19, transport input all, allow all protocols to enter the line20, int loopback0, enter Loopback0 interface21, IP host R1 2033 1.1.1.1, a host name for the 1.1.1.1 host22. Alias Exec CR1 Clear line 33 for Clear Line command23, privilege exec level 0 clear line, the command clear line to 0, in user m

DYNAMIC FA0/3 1 0013.7240 .0BFD Dynamic FA0/3 1 0021.8509.fb82 dynamic FA0/3 1 0022.4612.3c56 dynamic FA0/3 1 0025.115a.b932 Dynamic FA0/3 1 0025.11a7.9034 dynamic FA0/3 1 0090.7f84.5094 Dynam IC FA0/3 1 00e0.4c30.fd56 dynamic FA0/3 1 2851.3201.2498 DYNAMIC FA0/1 1 3c97.0e fd.b361 Dynamic FA0/3 1 7427.eace.90dd dynamic FA0/3 1 7427.eace.9259 dynamic FA0/3 1 782b.cb13.621d Dynamic FA0/3 1 8c89.a5e9.8317 dynamic FA0/3 1 8c89.a5e9.85ca DYN Amic FA0/3 1 b051.8e01.704c dynamic FA0/3 1 b051

The general router's access to set a lot of passwords, if not careful to forget the words that can be troublesome, without the password on whether there is nothing to do? Below, introduce a few simple commands to reset the route's password. In many ways, we choose Cisco Packet Tracer Simulator such tools to restore the password, generally before we start the router set a enable password and open the

Solve the Problem of waiting for the CISCO wrong command. When a command is wrong in the CISCO command line, the command always displays Translating "*******"... domain server (255.255.255.255) has to be stopped for several second

As we have mentioned earlier, the vro itself has an independent operating system and needs to face various complex network environments. Therefore, the configuration process of the vro is not a simple process. In addition to some basic configurations described in the previous article, many special configurations, such as Wan Protocol configuration and LAN protocol configuration, are also required in actual applications. This article describes the most common

The cisco 2621 router networking configuration command uses the cisco2621 router to form a small LAN, note: Configure command 1, configure the access password conf tenable secret flw521521line vty 0 4 password Authentication service password-encryption limit 2, configure int

file storage pathswitch# show users to see which users are logged on to the local device;switch# Clear Line (number) clears a specific user;switch# Show session to view the sessions initiated by the local device;switch# Resume {ID} quickly switches between sessions;Switch#disconnect/resume {ID} disconnects/restores the specified session;switch# Reload Restart the router device;switch# Show users to view the current logged-on user of the device;CTRL +

When a Cisco command line is wrong, the command always displays Translating "********"... Domain Server (255.255.255.255)It takes several seconds to stop and does not support interruption, Which is annoying. This is because IOS uses this command as a machine name for parsing. So it takes several seconds to stop. Log

"1" resolves the cisco switch password forgetting reset method:1, power off + the front panel hold down the mode key, and then re-power, always press the switch front panel port 1 indicates from green to off does not light off, automatically into the switch mode;2, input? See what configuration commands are (optional), enter "Flash-init" reset initialization, enter "Load-helper" to load the Help file, and see what "Dir flash" is in the Flash file. Fin

and status of an interfaceShow IP interface lists the state and global parameters of the interfaceShow IP protocols displays the parameters and current status of the active routing protocol processShow IP route displays the current status of the routing tableShow ip router displays IP routing table informationShow IPX interface shows the status of the IPX interface set by Cisco IOS software and the paramet

Using the DEBUG command can help us ts, but using the DEBUG command will usually output a lot of information, many of which are unnecessary and cause high CPU load, in this case, we can limit the debug output.You can apply the ACL to debug to limit that only the required debug information is output.For example, to view only ICMP packets from 1.1.1.1 to 1.1.1.2:Router