cisco rv042 router

Tags: Cisco CCNA router Password managementfor device security, the device administrator typically sets the user name and password for the device. Here's how to configure 3 passwords, with emphasis in the middle.Username Test password Cisco//This is to set up a layer of accounts and passwordsEnable password 123// This is the Setup admin passwordRouter (config) #l

Cisco port status: CSU ── channel server unit, DSU ── data server, unit, DTE ── DataTerminalEquipment 1. Serial * is down, line protocol is down (DTE) faults: [1] No power is added to the vro. [2] LINE is not connected to CSU/DSU. [3] hardware error. Solution: [1] Check power supply. [2] Check whether the cables and serial ports used are correct. [3] switch to another serial port. 2. Serial * is up and line protocol is down (DTE) faults: [1] local or

Global debugging When configuring a Cisco router, the boundaries between global and interface commands are obvious. In this case, we use "Global" to identify commands that cannot be used for interface debugging or specific transmission media types and Protocol debugging. For example, in vrouters 2500, you can use Debugging commands to analyze the Cisco Discovery

RIP and IGRP are commonly used router configuration protocols. What problems should we pay attention to when configuring RIP and IGRP? What should we do? The following configuration steps provide detailed answers. RIP Protocol RIP (Routing information Protocol) is an Internal Gateway Protocol (IGP) that is widely used earlier and is suitable for small-sized similar networks, is a typical distance-vector protocol. For more information, see RFC1058 an

1. Preparation Tools Cisco TFTP server, HyperTerminal, iOS files iOS files are not easy to find, you need to look at the hardware version, as well as the size of ROM RAM, to my Cisco 2621XM for example (with two fastethernet),Start looking for a few 2600 of iOS, the brush is not correct, the problem of unrecognized network interface, can not be configured, there should be F interface with S Ios,

In this experiment, the speed limiting device of a Cisco router is completed by a Cisco2811 router. In this experiment, we will first look at the flash: www.2cto.com yourname # dirDirectory of flash on the router in two ways: /1-rw-25438028 Oct 22 2010 02:25:58 + 02:26:08 c2800nm-ipbase-mz.124-15.T.bin2-rw-1505280 Oct

, dynamic address translation, and multiplexing dynamic address translation. The following example uses a Cisco router.1. Static address translationStatic address translation performs one-to-one conversion between the internal local address and the internal legal address, and specifies the legal address to which the conversion is required. If there are WWW servers or FTP servers in the internal network that

CHAP (Challenge Handshake Authentication Protocol) and PAP (Password Authentication Protocol) are generally used to provide security Authentication on PPP encapsulated serial lines. With CHAP and PAP authentication, each Cisco router is identified by a name to prevent unauthorized access. Task commands Set the PPP encapsulation ppp1 Set the authentication method ppp authentication {chap | chap pap | pap cha

This article describes how to control the BT traffic of a Cisco router through specific operations, and describes the specific operation methods in detail. I hope this article will help you. Network-Based Application Recognition (NBAR) indicates Network Application Recognition. NBAR is a technology that can dynamically search for protocols in Layer 4 to Layer 7. It can not only control static and simple net

are used The route of this packet. ---- GRE only provides encapsulation of data packets. It does not have encryption to prevent network listening and attacks. Therefore, in the actual environment, it often corresponds to an IP address. When the SEC is used together, IPSec provides encryption of user data to provide users with better security. The GRE protocol has two main purposes: internal protocol encapsulation and private address encapsulation. In China, CEN uses almost all TCP/IP protocols,

Probably a lot of people on the Cisco router speed limit is not a special understanding, so I studied the Cisco router speed limit detailed settings statement, here to share with you, I hope to be useful. In a Cisco router device,

CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common

that needs to be mapped to the Internet for access by others. The specific requirements are as follows:1. Only Internet users are allowed to ping the server and log on to the server through SSH;2. Only Intranet users are allowed to ping the server and log on to the server through telnet;3. Intranet users can access the Internet freely;4. The server cannot access the Internet.Step 1:First First, ensure that the server and PC can ping the gateway GW, then perform NAT on the GW, and ensure that t

When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available. Check on the Internet, the original switch port is Switchport, that is, the two-layer swit

This article describes how to enhance the security of a Cisco router by using a Nipper. So how should we use it? The following article gives you a detailed answer. How do I use a Nipper? Since Nipper supports so many devices and is also known to support a wide range of multi-functional options, it is impossible for me to present them in all aspects. However, we can make a basic demonstration. In our example

One. Test the topology:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/6E/CA/wKiom1WH46fhBjvJAADX2zoss3k937.jpg "title=" TP1. JPG "alt=" Wkiom1wh46fhbjvjaadx2zoss3k937.jpg "/>Two. Test ideas:A. Enable resolution by IP NAT without setting the direction---this way can be accessed directly from the public IP address, or can be accessed by domain name method---unfortunately Cisco is different iOS, some although have IP nat enable, but do not re

Necessity for configuring WRED on a Cisco Router Although the queue provides VoIP QoS congestion management, it still needs some congestion avoidance mechanisms, such as WRED. In particular, WRED can prevent the output queue from reaching the limit value, which will lead to the loss of all input packets. This article comes from Informit and discusses the necessity of configuring WRED on a

Cisco once again launched a new generation of router products and also applied new technologies. So I studied how Cisco developed the new VQE technology to solve the problem of IPTV Video Delivery. Here I will share it with you, I hope it will be useful to you. Cisco has announced the release of the VisualQualityExperi

Cisco IOS is a dedicated kernel that provides routing, switching, network interconnection, and remote communication capabilities. Most Cisco routers are running iOS, and more and more Cisco Catalyst switches are running it, including Catalyst2960 and Catalyst3560 series switches. Some important aspects of the Cisco

Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685)Cisco ASR1000 series router Denial-of-Service Vulnerability (CVE-2015-0685) Release date:Updated on:Affected Systems: Cisco ASR 1000 Description: CVE (CAN) ID: CVE-2015-0685The