cisco save config command

-interface IP address.CliSwitchSwitch (config) #vlan 2Switch (Config-vlan) #exitSwitch (config) #vlan 3Switch (Config-vlan) #exitSwitch (config) #int F0/2Switch (config-if) #switchport Access VLAN 2Switch (

1. Compilation and Connection In general, if the header file of the library is not in the/usr/include directory, you need to use-IThe parameter specifies its path. Because the same library may be located in different directories on different systems, users can install the library in different directories during library installation, even if the same library is used, because the library pathThe path of the header file specified by the-I parameter may be different. The result is that the compiling

The COPY command is often used during vro configuration. Next we will introduce how to use the COPY command to back up the configuration file, and how to COPY the backup configuration file from the TFTP server. Figure 1 1. copy running-config startup-config This

The cisco 2621 router networking configuration command uses the cisco2621 router to form a small LAN, note: Configure command 1, configure the access password conf tenable secret flw521521line vty 0 4 password Authentication service password-encryption limit 2, configure interface IP enableconf tinter fa0/0ip address 192.168.2.2 255.255.255.0no shutdown inter fa0

"Data Collation" Cisco [Shell, Command]Promotmode{usermode:router> (input:enable) privilegemode:router# (input:conft) Globalconfigmode:router (Config) #----ctrl-z->pm,exit-> Gcminterface:router (config-if) #Sub-interface:router (config-subif) #Controller: Router (

1, enable (can be abbreviated to EN), from user mode into the privileged mode2, configure terminal (can be shortened to Conf t), enter the configuration mode3, Interface g0/0 (this interface can be changed), enter the Gigabit Ethernet interface mode4, IP address 10.61.100.1 255.255.224.0, configure IP addresses5, no shutdown, activation interface6, line vty 0 4, enter the virtual terminal vty 0--vty 47. Password Cisco-

"1" resolves the cisco switch password forgetting reset method:1, power off + the front panel hold down the mode key, and then re-power, always press the switch front panel port 1 indicates from green to off does not light off, automatically into the switch mode;2, input? See what configuration commands are (optional), enter "Flash-init" reset initialization, enter "Load-helper" to load the Help file, and see what "Dir flash" is in the Flash file. Fin

Solve the Problem of waiting for the CISCO wrong command. When a command is wrong in the CISCO command line, the command always displays Translating "*******"... domain server (255.255.255.255) has to be stopped for several second

Switch Password settings: Switch>enable into privileged mode Switch#config terminal into global configuration mode Switch (config) #hostname set the host name of the Exchange Switch (config) #enable secret XXX To set the privileged encryption password Switch (config) #enable password Xxa set privileged non-secret

memoryShow processes process for displaying routersShow protocols protocol for display settingsShow protocols displays the configured protocols. This command shows the status of any configured layer 3rd protocolShow Running-config Displays current configuration information in RAMShow Spantree displays spanning tree information about a virtual local area network (VLAN)Show stacks monitors and interrupts the

When a Cisco command line is wrong, the command always displays Translating "********"... Domain Server (255.255.255.255)It takes several seconds to stop and does not support interruption, Which is annoying. This is because IOS uses this command as a machine name for parsing. So it takes several seconds to stop. Log

Using the DEBUG command can help us ts, but using the DEBUG command will usually output a lot of information, many of which are unnecessary and cause high CPU load, in this case, we can limit the debug output.You can apply the ACL to debug to limit that only the required debug information is output.For example, to view only ICMP packets from 1.1.1.1 to 1.1.1.2:Router (c