cisco shaping

Cisco Terminal configuration: (DHCP only)Service DHCPIP DHCP relay information trust-allInterface Vlan4IP address 192.168.4.254 255.255.255.0IP helper-address 10.0.0.11!Interface Vlan6IP address 192.168.6.254 255.255.255.0IP helper-address 10.0.0.11!650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/59/7E/wKioL1TUvvqTNu5WAASFSbihEBY376.jpg "title=" 2015-02-06_21-11-28.png "alt=" Wkiol1tuvvqtnu5waasfsbiheby376.jpg "/>2, the common configuration

Introduction after you log in to the CISCO switch, we will need to use some common operations, such as querying, restarting, and so on, where some of the commonly used operations are grouped together. Query HelpIn different modes, we can enter the question mark directly (? You can query all the commands that you can use in the current mode. When entering a command, if you do not remember the full name of the command, enter the first few characters

LAN is not changed, and the configuration and access control list of the external network Port WAN needs to be changed .Increase the configuration of the VPDN. Assuming the username is admin, password 123456, the configuration process is as follows:This case is XX Telecom ADSL PPPoE access, need to use a common ADSL modem and a Cisco 2600 router (dual Ethernet port), IOS 12.2 (), can realize LAN sharing Internet.　　This case configuration is divided i

Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure simple dynamic routing, thus reducing the workload.Configuration ideas1 Configure the IP

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Tags: routing switching technology HSRP working principle three-layer Exchange STP function DHCP serviceFirst, the questionDay 011. What is a Vlan? What does VLAN do? is the interface of the default switch in that VLAN? What kind of Vlan??2. What is Trunk? What is the mode of Trunk? How to negotiate?3. What is the role of EtherChannel?4. What is DHCP? What is the role of DHCP?Day 021. What is the three layer Exchange? What is the difference between a two-layer switch and a three-tier switch and

Day 051. What is NAT? What are the implementation methods?NAT (Network address translation): By translating the private IP address of the internal network into the world's only public IP address, the internal network canTo connect to an external network such as the Internet.How NAT is implemented:The corresponding relationship of the IP address is one-to-one, and is constant, with the help of the static transformation, it can realize some specific service in the external network.Access to the se

Using Cisco to build an experimental environment I.. Configure DHCP client;Two, configure the switch SW1SW1 (config) #vlan 10SW1 (Config-vlan) #exSW1 (config) #vlan 20SW1 (Config-vlan) #exSW1 (config) #int FA0/1SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 10SW1 (config-if) #no shutdownSW1 (config) #int FA0/2SW1 (config-if) #switchport mode accessSW1 (config-if) #switchport Access VLAN 20SW1 (config-if) #eSW1 (config

Cisco CCNA Chapter 7 answers for the third semester, Cisco ccna for the third semester 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.

Cisco CCNA Chapter 6 answers for the third semester, Cisco ccna for the third semester 1. 2. 3. 4. During the implementation of inter-VLAN routing, what are the important considerations when configuring the sub-interface of the router? The physical interface must have an IP address. The sub-int

, adding switches and end devices1, double-click switch into switch command line (CLI) mode, switch configuration mode by command2 in most cases for security reasons, you need to configure the switch privileged mode passwordValidation test3 Configuring the telnet login switchTo achieve remote login, first need to configure the login user and device management addressVerify the configuration by matching the IP address of the PC with the switch management address into the same network segment and

Technical standards for VLANs IEEE 802.1Q was formally promulgated by IEEE Commissioners in June 1999, and the earliest Vlna technology was proposed by Cisco (Cisco) companies in 1996. With the development of the past few years, VLAN technology has been widely used in large and small enterprise networks, becoming the most popular Ethernet LAN technology at present. This article is going to introduce one of

Tags: size src zone sha port text topology Cisc-oTwo networks in different regions if you want to communicate, you need to configure routing on the router to implement the packets across the networkRouters can connect to multiple networks, but the router itself does not know about other networks, and we need to manually configure static routes to let routers know about other network information or to configure dynamic routing to let routers learn about other networks themselves.This learning con

Tags: color-o switch test one-arm routing access via interface implementation representationTo achieve inter-VLAN communication, in addition to configuring the SVI interface on the switch, you can also implement VLAN data forwarding by configuring sub-interfaces under the physical interface of the router.Configuration ideas:1 The access switch configures the corresponding VLAN and sets the access PC port to access mode2 Setting the physical interface of the router to which the switch is connecte

Nat[network address translation] In the absence of IP address in the case of a great use, it can not be normal Sisu network of the intranet address into a legitimate external network address on the public network to send and receive data. At the same time address translation function can also be very good to hide and protect the host network.Nat has static NAT (internal address and external address one-to-one) and dynamic NAT (internal address pool and external address Pool A-do)This time we'll

Network address port Conversion NAPT is a very familiar way of transformation. NAPT is commonly used in access devices, which can hide small and medium-sized networks behind a legitimate IP address.Unlike dynamic address NAT, NAPT maps An internal connection to a separate IP address in the external network, adding a TCP port number selected by the NAT device to the address.This time, let's get to know napt.Configuration ideas1 Configure the router's interface IP address, note the network segment

RIP protocols can be configured in a more convenient way, but the limitations of RIP itself indicate that it is not suitable for medium to large networks. In contrast, OSPF is more complex to configure than RIP, but its functionality and performance are better than RIP.Configuration ideas1 Configure the physical interface address of the router Xia Lian switch and the physical interface address of the router to the other router and open the port2 Configure the address of the switch Xia Lian PC an

Through the previous experiment we learned that by configuring VLANs, the terminals under different VLANs could not communicate with each other, but if you wanted to communicate between different VLANs, you would need to configure inter-VLAN routingLayer three switches have the capability of the network layer and can be forwarded via the routing functionNetwork environment1 set the IP address and gateway of the terminal (192.168.1.1 and 192.168.2.1, respectively).2 VLAN is configured under Layer

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.1