cisco switch 10gb ports

, the fiber channel switch. Scalability not only refers to the capacity for increasing network bandwidth, but also whether to use the number of ports of existing fiber channel switches to effectively build a large-scale storage network. With the increasing demand for storage networks, users urgently need a high-performance, powerful storage network platform that can meet the bandwidth and port quantity requ

a port interface VLAN n in each VLAN ), correctly explains ARP settings for Cisco switches.6509 MSFC # ping 10.10.1.65Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.10.1.65, timeout is 2 seconds:Success rate is 100 percent 5/5), round-trip min/avg/max = 1/1/4 MS6509 MSFC # show arp | in 10.10.1.65Internet 10.10.1.65 2 0006.2973.121d ARPA Vlan2 Through the above Cisco

): can only receive or send bpdus messages learning (learning) : can receive or send BPDU Message, and form mac forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by defa

In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear at a glance. If you do not have this software, you can use the following manual analysis method to find the answer: Ex

Droppe d:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Until This step, creating and configuring VLANs has been done on the Linux box. Now we is going to configure VLAN and trunk on the Cisco Catalyst switch.4. Configure Cisco Catalyst

, indicating electrical PortTC: Applicable to switch 2918,2928 and 2960, indicating electrical port + SFP dual-media portLT: includes two kinds of hybrid electrical ports: common electrical ports and POE electrical portsLC: Includes POE electrical port + common electrical port + 2SFP dual-media port and two hybrid electrical portsTS: Applicable to, indicating ele

Port security Configuration for the Cisco PT Simulation Experiment (7) switchExperimental Purpose : Master the port security function of the switch, control the user's secure accessExperimental Background : The company network adopts the personal fixed IP Internet program, in order to prevent the company internal User IP address borrowing, using, unauthorized access to the

#config terminal Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users) Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption) Route (config-line) # login ---- encrypted upon login Route(config-line)#exit Continue to enter the privileged mode and wh

Cisco mds9222i Fibre Switch most commonly used debug commands1. Check the switch portShow interface [Interface-range]View specified port run status, WWN information, configuration parameters, and packet statistics.Demonstration:mds9222i-1# Show Interface FC1/1FC1/1 is trunking-port FC1/1 operating normally, is a TE portHardware is Fibre Channel, SFP was short wav

management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server.Note: by default, the Catalyst 5000 series switches are VTP servers.Cat5002> (enable)Cat5002> set vtp domain cisco mode clientTrunk ports)VLAN Trunk protocol (VTP) is transmitted only on the Trunk port (ISL, LANE, and 802.10) and should be t

switch is a gigabit switch (all interfaces are gigabit)TT: Indicates that the gigabit on-connection port of the switch is base-t (i.e.: RJ45 interface)TC: Indicates that the switch gigabit on the port is dual-use, directly with the BASE-T, you can add modules on it.TS: Indicates that the 37

The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of ports