cisco switch cable

A Cisco 4506 switch in the user's actual environment could not log on, and the system could only be cracked because the maintenance staff did not remember the modified password.Environment:Cisco Catalyst 4506E switch, engine for WS-X45-SUP8-E, system version is cat4500es8-universal-mCrack steps:To restart the switch, p

message are correctIf a large number of messages are sent, the network bandwidth will be exhausted to form another Denial-of-Service attack.3. The client can specify the IP address at will.The client does not have to use the DHCP service. It can set IP addresses in a static way. If any,This will greatly increase the possibility of network IP address conflict.II. Introduction to DHCP Snooping TechnologyDHCP Snooping is a DHCP security feature. Cisco s

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r

and a switch are connected with the console lineHow it works: Switch password recovery fundamentals: Change the Config.text file name in the switch to a different file name, and then enter the configuration mode to change the password, and finally restore the Config.text file nameSteps:1. Power off first2. Power off while holding down the mode key on the

Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracert three-tier switch VLAN configuration-Ibm.chick-mingkang.zhou "src=" Http://img2.ph.126.net/2N Qfixjyba1gdiqtbuknhq==/6630601572768576164.png "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the three layer switch divides three VLANs, is Vlan2\vnal3\vlan4, and the V

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL

templateHOST_NAME h17_2960sw1_3.251Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}Define Service{Use GENERIC-SERVICE,SRV-PNP; Inherit values from a templateHOST_NAME h18_2960sw1_3.247Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}6. Configure permissions (pending validation)[Email protected] ~]# chmod 777/var/tmp/check_traffic_10.10.3.249_10128.hist_dat_root__647. Restart the Nagios service[E

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch# Clear License All4. Disable and enable Telnet and SSHswitch# Config TSwitch (config) # no Telnet server enableSwitch (config) # Telnet Server enableswitch# Config TSwitch (config) # SSH server enableSwitch (config) # no SSH server ena