cisco switch gui interface

Cisco switch Product Name Description Catalyst nn xx [-C] [-M] [-A/-EN] NN is the serial number of the switch XX for A fixed configuration switch is the number of ports, for A modular switch, the number of slots C indicates that the fiber-optic

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

trunkSwitch (config-if) #switchport trunk allowed VLAN, set allowed VLANsSwitch (config-if) #switchport trunk encap dot1q; set VLAN trunkingSwitch (config) #vtp domain; Set the VTP domain nameSwitch (config) #vtp password; set the VTP passwordSwitch (config) #vtp mode server, setting the VTP patternSwitch (config) #vtp mode client, setting the VTP patternSwitch set IP address:Switch (config) #interface vlan 1; go to VLAN 1Switch (config-if) #ip addre

message are correctIf a large number of messages are sent, the network bandwidth will be exhausted to form another Denial-of-Service attack.3. The client can specify the IP address at will.The client does not have to use the DHCP service. It can set IP addresses in a static way. If any,This will greatly increase the possibility of network IP address conflict.II. Introduction to DHCP Snooping TechnologyDHCP Snooping is a DHCP security feature. Cisco s

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users using the following command:Privilege EXEC l

Enable SNMP on the switch and configure the community name (Swap changer IP192.168.5.209)Switch (config) #snmp-server Community public roSwitch (config) #snmp-server Community public RW 2. Get the index information for the switch by entering the following command on the Nagios server[Email protected] ~]#/usr/local/nagios/libexec/check_traffic.sh-v 2c-c publi

Tags: cisco/remote configurationIn actual work our routing and switches are always placed in the room to facilitate our work we need to configure the routing and switches so that we can configure the routers and switches in the office or at home.This is a simple network topology diagram where a computer-connected route configures the switch across network segmentsFirst we determine the PC ip:192.168.1.1 255

We have explained a lot about the configurations of CISCO switches. Here we will mainly explain the port security configurations of CISCO 3550 switches. Scenario: There is a CISCO3550 switch in a certain unit. For the sake of network security, the security requirements for some ports are high, that is, only the specified host can be connected, for example, if you

Microsoft's Windows Server 2012 has been able to support LACP link aggregation, due to the use of link aggregation can achieve line redundancy and bandwidth increase, here I used a Cisco 2960 to do a test for interested friends reference.Experiment Preparation:Cisco switch 29,601, install server 2012 servers, there are two Gigabit network card, network cable two root.Steps:1. Configuration of

protected] bonding] # ethtool EM2Settings for EM2:Supported ports: [TP]Supported link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullSupports auto-negotiation: YesAdvertised link modes: 10 BaseT/half 10 BaseT/full100 Baset/half 100 Baset/full1000 Baset/fullAdvertised pause frame use: NoAdvertised auto-negotiation: YesSpeed: 1000 MB/SDuplex: fullPort: Twisted PairPhyad: 1Transceiver: InternalAuto-negotiation: OnMDI-X: UnknownSupports wake-on: GWake-on: dLink detect

Cisco switch Basic configuration: Console Port connectionUser mode hostname#;Privileged mode hostname (config) #;Global configuration mode hostname (CONFIG-IF) #;Switch Password settings:switchgt;enable; Enter privileged modeSwitch#config terminal; Go to global configuration modeSwitch (config) #hostname Csico; Set the host name of the switchSwitch (config) #enab

switch forgot password, no relationship, restore to factory settings, restarted. Switch on and hold down the switch's mode button. Go to switch: Input Flash_init Del Flash:config.txt Del Vlan.dat Boot Go to the following interface and reconfigure the switch