Cisco switch setup tips: MAC address, Technology Square: settings and skills of two CISCO switches, mainly: Cisco switch setup skills to find the MAC address corresponding to the IP address, cisco
How to configure IP address and MAC address on a Cisco switch binding Content Summary: at present, many of the company's internal network, has adopted the MAC address and IP address binding technology. Here we will introduce the configuration of IP address and MAC address bindings for Cisco switches. Description: at present, many of the company's internal
Cisco, as a leader in the routing industry, is still very advanced in technology and has continuously emerged in new products. Currently, the 8400 series of routing switches provide the backbone network functions required for transmission. If you are an Enterprise Information System expert, you will understand that it is a severe challenge to provide high-quality voice, data, and multimedia services to enterprises while controlling costs. Today, Cisco
In the network World, Cisco System Inc. Nobody knows, no one does not know. With its IOS (Internet operating System), Cisco is an absolute leader in the multiprotocol router market. Currently, nearly 80% of the routers in the Internet are from Cisco. In fact, in addition to the main product of the router, Cisco also ha
[Cisco] DHCP relay, layer-3 Switch VLAN Routing PracticeThe experiment topology uses the GNS3 0.8.6 simulator to build a DHCP server using Red Hat 6.5. The experiment requires configuring a layer-3 Switch VLAN routing so that VLAN10 and VLAN20 members can access each other. Performs DHCP relay for layer-3 switches so t
Company a device, Ws-c2960s-24ts-l, is the Cisco 24 Port 1000M Two layer Exchange Yang, the use of iOS version of 12.2 (UNIVERSALK9-M) iOS software, the company recently installed some digital cameras, The monitoring host and a billiard-type monitoring to the machine, the interface of the transmission rate is much larger than the rate of ordinary office, the following is the rate of the two interfaces I copied.G1/0/3 (Monitoring host interface)5 minut
There are still many things worth learning about Cisco switches. Here we mainly introduce the Cisco switch interface mode. In a Cisco switch network, there are four main types of interfaces in the LAN that are ultimately stable: access/trunk/multi/dot1q-tunnel.
1. access: it
First of all, the Cisco, the orders are not many, are basic. Not including STP, upgrades, Acl,web and the like.Ruijie and Cisco 99% are similar.CISCO layer-2Switch>go to HyperTerminal console switch>Enable access switch privileged mode switch#configure terminal Enter
The naming rules for Cisco switches are more complex than the naming rules for routing,Look at these:ws-c2960-24tc-l, WS-C2950G-24-EI-DC, Ws-c2960-24tt-l, Ws-c3750g-24ts-e, Ws-c3750g-24t-s, We didn't find them on the switch, we just saw the Catalyst 2950 series and wrote it all: The Cisco Catalyst 2950 Series, which means the
The detailed steps for restoring the password of a Cisco switch are illustrated. If the password of a Cisco switch is improperly restored, the password will be lost. Today, we will contact the steps for restoring the password of a Cisco
CISCO router device categoryThe name rules of cisco routers start with cisco, such as cisco2611 and cisco2610. cisco is the name of the device manufacturer, 26xx represents the 2600 series routers, and xx is a more detailed classification. The following lists several common series of
#config terminal
Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users)
Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption)
Route (config-line) # login ---- encrypted upon login
Route(config-line)#exit
Continue to enter the privileged mode and wh
In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear at a glance.
If you do not have this software, you can use the following manual analysis method to find the answer:
Ex
Cisco mds9222i Fibre Switch most commonly used debug commands1. Check the switch portShow interface [Interface-range]View specified port run status, WWN information, configuration parameters, and packet statistics.Demonstration:mds9222i-1# Show Interface FC1/1FC1/1 is trunking-port FC1/1 operating normally, is a TE portHardware is Fibre Channel, SFP was short wav
The article I want to share and configure VLAN on Linux through Cisco Catalyst Switch.Requirements:1. Linux installed on a PC with one or more NICs (Network Interface Card). I Use the Centos 5.4 using 2.6.18-164.11.1.EL5PAE kernel. It should is applicable on other Linux distros such as Slackware, Ubuntu, Fedora, Debian, etc.2. Cisco Catalyst Switch 29503.2 Pc/lap
Cisco switch,
Cisco switchesSwitch> enable
Switch # con
Switch # conf
Switch # configure ter
Switch # configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
#十二步 Save ConfigurationDestination filename [startup-config]?Building configuration ...[OK]switch#-=--------Switch#reload#重新启动-----------Press RETURN to get started!00:00:14:%spantree-5-extended_sysid:extended sysid enabled for type VLAN00:00:17:%sys-5-config_i:configured from memory by console00:00:17:%sys-5-restart:system restarted--Cisco Internetwork Operating
): can only receive or send bpdus messages
learning (learning) : can receive or send BPDU Message, and form mac
forwarding (Forwarding) : can receive or send BPDU Message, and form mac Address table, send and receive data frames simultaneously
STP Convergence: All ports on the switch are converted to forwarding or blocking mode, which takes 50 seconds by default. The
Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password protection.Switch>enable #进入特权模式
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.