cisco valet router

Application (ACL) of the access control list of cisco router Integrated Experiment ii ip Address Configuration on each device, steps ======================================================== ========================================================== ======================================= Configure route R1: (config) # ip route 0.0.0.0 0.0.0.0 192.168.1.254 route www.2cto.com R2: (config) # ip route 0.0.0.0

NAT configuration instance for cisco router with port ing If the ISP provides many IP addresses, you can use NAT to map an external address to each server. However, if it is not the case (for example, if it is only two times), there are four servers in the Intranet that need to provide external services, one for Intranet address translation and the other for providing services on the Internet.Interface fast

whether you have loaded an IPSec IOS image that supports SSH. In our example, we will use the Cisco IOS command. Run the following command:Router> Show flashThis command displays the name of the loaded IOS image. You can use the result to compare the list of supported features of your supplier.After you verify that your device supports SSH, make sure that the device has a host name and a correctly configured host domain, as shown below:Router> config

Network MapGoal:from Workstation telnet remote switchEnvironment:cisco Packet Tracer650) this.width=650; "class=" Media "src=" Http://www.davis-wiki.com/lib/exe/fetch.php?media=cisco_router:telnet.jpg "/>Condition1:switch 12:workstation 13:network Cable 1SettingsWorkstation SettingsStatic ip:192.168.1.2255.255.255.0192.168.1.1Switch Settings650) this.width=650; "class=" Media "src=" Http://www.davis-wiki.com/lib/exe/fetch.php?media=cisco_router:telnet1.jpg "/>TestTry telnet on workstation. Resul

How to configure remote logon for a Cisco router IP Address Configure the vro IP Address Run the command ip address x. x to configure the ip address. The command is as follows:Router2800> enable (in privileged Mode)Router2800 # configure termial (entering global configuration mode)Router2800 (config) # int f0/1 (enter Interface Configuration Mode)Router2800 (config-if) # ip address 192.168.0.1 255.255.255

Cisco router VLan isolation LAN broadcast packet configuration experiment and summary, ciscovlan 1. Tutorial Description: connect to and set the IP address of the PC according to the network topology. PC1 and PC2 are required to be accessed on VLAN 12, while PC3 and PC4 are accessed on VLAN 34, PC1 and PC2 are interconnected, PC3 and PC4 are interconnected, and VLan 12 and VLan 34 are interconnected to isol

EnConf tHostname Cisco3800Interface Loopback0IP address 6.6.6.6 255.255.255.0Interface fastethernet0/0Description WANIP address 119.200.27.50 255.255.255.252IP Nat ousideInterface FASTETHERNET0/1Description LANIP address 192.168.6.1 255.255.255.0IP nat InsideIP Route 0.0.0.0 0.0.0.0 113.200.27.49 Telecom Unicom Next hopIP Route 192.168.3.0 255.255.255.0 192.168.6.2IP Route 192.168.4.0 255.255.255.0 192.168.6.2IP nat Pool www 119.200.27.50 119.200.27.55 netmask 255.255.255.252IP nat inside source

With the development of the routing industry, the market demand is more extensive, but many users still do not understand the routing configuration issues. Here we mainly provide a comprehensive description of the Cisco router NAT configuration. More and more INTERNET resource sharing methods are available. In most cases, ddnleased lines are widely used with their stable performance and good scalability. DD

Recently, a friend asked me how to configure static NAT for a Cisco router to allow Internet users to access the Intranet Web and email servers through a Cisco router. Obviously, this function requires NAT between the public IP address and the Intranet IP address. The following are the specific implementation methods.

The market demand for Cisco routers has been very high. Here we mainly analyze the detailed knowledge of Cisco router configuration and RJ45 console connection, for accessing and configuring I0S on a new router, we must communicate with the Console port. After connecting a console terminal with the Console port configu

It is very important to know some common knowledge about CISCO routers. Here we mainly explain the CISCO router tutorial, which provides a detailed analysis from configuration to access methods. This document uses Cisco2620 as an example to describe how to configure the vro and remote access, this article discusses how to use the DHCP service function of the inte

Recently changed jobs, the company more than 40 people share a 20M bandwidth wireless network, the router for Cisco R2911. Boss, let me make a cacti to monitor Cisco routed network card traffic. The whole days can not get the SNMP data, finally to the routing permission to find that the last operation to the routing SNMP service off, leaving the document written

Cisco router configuration mode In general, you can configure your router in 5 ways: 1.Console Port connection terminal or running terminal simulation software of the microcomputer; 2.AUX Port Connect modem, connect with remote terminal or computer running terminal simulation software by telephone line; 3. Via the TFTP server on the Ethernet; 4. Adoption of

For enterprise users, multi-device port access control can optimize the network more reasonably. Here we analyze in detail how to configure a Cisco router to implement this function. You only need a CISCO router with an asynchronous module or a router with a built-in asynchr

The importance of vro configuration is self-evident. Here we mainly analyze the Cisco router configuration statements in detail, and share them with you here, hoping to help you. Introduction to Cisco router configuration Cisco ios operating environment. ROM monitor>

For many beginners, using cisco rommon to maintain a vro, the ROM Monitor of a cisco router is often unfamiliar or even daunting. The reason is simple. First, we do not often use this mode, I am not familiar with the related operations. Second, Operation errors in ROM Monitor mode often cause fatal damage to the vro (such as destroying the IOS file in flash, lead

The command line port of a cisco router uses a hierarchical structure, which requires logging on to different modes to complete detailed configuration tasks. From a security perspective, cisco IOS divides EXEC sessions into USER mode and privileged mode. Features of the USER mode: In USER mode, only basic monitoring commands are allowed. In this mode, the confi

access vlan 4 Switch (config-if) # no shutdown Switch (config-if) # exit Switch (config) # interface f0/3 Switch (config-if) # switchport mode trunk sets this port to relay mode) Switch (config-if) # no shutdown Witch (config-if) # exit. You can directly use ctrl + z or end to exit the privileged mode) 2. Configure single-arm routing on vrocisco Cisco 2611) Router # con

There are many things worth learning about the configuration mode of a Cisco router. Here we mainly introduce the mode of user execution and privilege of a Cisco router. Ping is the most commonly used troubleshooting command. It consists of a group of ICMP response request packets. If the network runs normally, a group

Basic configurations of Cisco routers and switches: www.2cto.com Router> \ enter the user mode Router when the vro is started> enable \ type the command to enter the Router mode # \ This display mode indicates that the Router mode has been entered # configure terminal \ type