clear cisco switch config

trunkSwitch (config-if) #switchport trunk allowed VLAN, set allowed VLANsSwitch (config-if) #switchport trunk encap dot1q; set VLAN trunkingSwitch (config) #vtp domain; Set the VTP domain nameSwitch (config) #vtp password; set the VTP passwordSwitch (config) #vtp mode serve

Lab Environment:650) this.width=650; "alt=" Cisco Packet Tracer three-layer switch interrupt Dhcp-ibm.chick-mingkang.zhou "src=" http://img0.ph.126.net/4fx 93s0ahtpaead19pxmyg==/6619563575538146055.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>Experimental Purpose:1, the VLAN is divided on the three layer switching: vlan10\vlan100\vlan200, and the IP is specified as: 192.168.10.254\ 192.16

In a Cisco switch, how does one configure QOS speed limit? How to restrict BT download? This blog will use detailed examples for your explanation. Instance 1: QOS speed limit problem on CISCO switches It is used to control the bandwidth of a leased line user on a vswitch. The vswitch is usually at 10/100/1000 or three rates. QOS is required for other rates. You c

-if) # channel-group 1 mode desirable Switch (config-if) # end Appendix: Switch (config-if) # channel-group port_channel_number mode {auto | desirable | on} // Add the physical port to an Ethernet channel and determine the PagP mode. 3) layer-2 Ethernet Channel Configuration

First of all, the Cisco, the orders are not many, are basic. Not including STP, upgrades, Acl,web and the like.Ruijie and Cisco 99% are similar.CISCO layer-2Switch>go to HyperTerminal console switch>Enable access switch privileged mode switch#configure terminal Enter

#config terminal Route (config) # line vty 0 4 ---- enter telnet remote login port mode (0 4 allows 5 Users) Route (config-line) # password CISCO ---- set the password to "CISCO" (to encrypt the password, enable vro password protection before: service pass-encryption) Rou

current configurations# copy running-config Startup-config saves the current configuration in RAM into the NVRAMS> show interface [Type slot_#/port_#] View information for all or specified interfacesS> show IP Display IP configuration of the switch (available on 1900 series only)S> Show version View device informations# show ip interface brief verify IP configur

Experimental topology Router (config) #frame-relay switching to simulate a router as a Frame relay switch Router (config) #inter S1/1 Router (config-if) #clock rate 128000 Router (config-if) #encapsulation Frame-relay Configuration Interface encapsulation and binding r

Cisco switch, Cisco switchesSwitch> enable Switch # con Switch # conf Switch # configure ter Switch # configure terminal Enter configuration commands, one per line. End with CNTL/Z.

Droppe d:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Until This step, creating and configuring VLANs has been done on the Linux box. Now we is going to configure VLAN and trunk on the Cisco Catalyst switch.4. Configure Cisco Catalyst

VLAN configuration status show vlan Test Trunk Create a relay on a specific portSettrunkmod_num/port_num [on | off | desirable | auto] [vlans] Check the relay configuration statusShowtrunk Spantree settings Set in a vlanSpantreesetspantreeenable [vlan] Set the bridging forwarding latency in a vlanSetspantreefwddelaydelay [vlan] Set the hello message sending interval in a vlanSetspantreehellointerval [vlan] Sets the maximum duration of a vlan connection.Setspantreemaxageagingtime [vlan] Set the

Branch switches.The Cisco switch can support any media as a trunk line. To achieve relay, you can use its unique isl tag. Isl (inter-switch link) is a protocol for transmitting vlan information and vlan data streams between switches, between switches and routers, and between switches and servers, by configuring isl encapsulation on the port directly connected to

MAC address on the switch. In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear

1). Configure the VLAN Port Number of the switch named Switch1 as follows: Switch1(config)#int e0/2Switch1(config-if)#vlan-membership static 2Switch1(config-if)#int e0/3Switch1(config-if)#vlan-membership static 2Switch1(config