comcast internet router

The TP-link router comes with a ping tool, which I used to think is a chicken fault, because I am used to using the ping tool of Windows command line, which can be in the local network, it is convenient to ping the IP addresses of this website or different networks. Recently, when I was at home and needed to control the company's routers, I found a problem: I was unable to ping the company's internal network IP through the command line of my home com

1. Wiring modeFirst, connect the DI-504 's own AC power adapter to its rear panel, and then plug the adapter into your power outlet. The Power LED indicator light on the front panel indicates that the operation is correct.Plug one end of an ethernet cable into the WAN port on the DI-504 rear panel and the other end into the Ethernet port on your dsl/cable modem. The LED light on the WAN port of the DI-504 front panel indicates that the operation is correct.Plug one end of another ethernet cable

Article Title: Use the PPPoE router to dial up the internet under ipvtn8.04. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. 1. set PPPoE. first start the modem, and then select Applications → Accessories → Terminal to open the SHELL Terminal. Enter the following comma

Failure problem: There are two computers to share the Internet, so the broadband router installed, but even if only one computer in the Internet, the speed is very slow. Fault handling: Sharing the Internet via broadband routers can cause a certain loss of Internet speed, w

1. This method is suitable for the cat comes with the dialing function, 4G wireless cat and other devices, the other steps and the usual configuration router step is no different, only when the WAN port configuration changes. 2. First IP-DHCP client Click the plus sign to add, select the WAN port is the number of ports, and then determine. Wait a few seconds for the DHCP client interface to show that the IP address indicates a successful connection. o

Connect a GNS analog router to the Internet1. Environment: XP system, GNS3.0.7.2 integrated SecureCRT (or SecureCRT is not available)Preparation: add the Loopback adapter virtual network card under the XP system, an ADSL dial-up connection2. Network Connection Configuration:7. Select R1, right-click, and click Start. Then, right-click R1, click "Console" to display the SecureCRT configuration Console integrated with GNS (if SecureCRT is not integrated

Build PPPoeServer with the home ADSL line and use the CISCO router to enable the PC to access the Internet www.2cto. comR1 (config-if) # doshrunBuildingconfiguration... Currentconfiguration: 1470 bytes! Version12.4servicetimestampsdebugdatetimemsecservicetimestampslog Use the home ADSL line and use the CISCO router to build the PPPoe Server so that the PC can acc

A lot of people ask every day why serve something mapping? For example: Through the router to the Internet, the site can be accessed by themselves, but others can not; input 127.0.0.1 to access, others still can't see; input localhost can be seen, but others just can't see, irritating ah ~ no way, only port mappingHttp://baike.so.com/doc/2884143.htmlThe following is a company from the external network acces

2, (a light cat) to the light cat out of a network cable to connect the router's WAN (blue logo), and then find a short network cable, a computer, a router 1/2/3 arbitrary interface (yellow), wiring mode as shown below: Note: When powered on, the router is working normally with the SYS LEDs flashing, WAN LEDs illuminated steady or blinking, and the 1/2/3 port LEDs attached to the co

1. Wiring mode First, connect the DI-504 's own AC power adapter to its rear panel, and then plug the adapter into your power outlet. The Power LED indicator light on the front panel indicates that the operation is correct. Plug one end of an ethernet cable into the WAN port on the DI-504 rear panel and the other end into the Ethernet port on your dsl/cable modem. The LED light on the WAN port of the DI-504 front panel indicates that the operation is correct. Plug one end of anoth

The first thing to be sure is that the work of the router is normal, and this usually happens because of the following situations: 1 The IP Address, gateway and DNS of this computer are not set or set incorrectly; 2 The firewall in the router will be the computer's IP or MAC address filtered out, resulting in this computer can not normal Internet; 3 So

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco routes to achieve shared Internet accessCisco routers configure NAT, how to use static rout

Mercury MW300R router wireless broadband Internet access settings tutorial, mw300r wireless broadband Wireless Broadband route Internet access settings (mercury MW300R) First, Click Internet Explorer ). Open Internet Explorer and enter (192.168.1.1) in the address

LINUX as a host, share Intranet Internet access (use LINUX as a simple router)-Linux Enterprise Application-Linux server application information, the following is a detailed description. LINUX network settings: Intranet IP Address: 192.168.0.1 (as long as it is in the same network segment as WINDOWS) Subnet Mask: 255.255.255.0 Gateway: NULL (automatically obtained) DNS: according to data centers in diff