configure dhcp on cisco router

Recently, a friend asked me how to configure static NAT for a Cisco router to allow Internet users to access the Intranet Web and email servers through a Cisco router. Obviously, this function requires NAT between the public IP address and the Intranet IP address. The following are the specific implementation methods.

(Config-vlan) #exitSwitch (config) #int fa0/1 add our FA0/1 to VLAN2Switch (config-if) #sw mo acSwitch (config-if) #sw AC VLAN 2Switch (config-if) #exitSwitch (config) #int FA0/2 add our FA0/2 to VLAN3Switch (config-if) #sw mo acSwitch (config-if) #sw AC VLAN 3Switch (config-if) #exitSwitch (config) #int FA0/3 add our FA0/3 to VLAN4Switch (config-if) #sw mo acSwitch (config-if) #sw AC VLAN 4Switch (config-if) #exitSwitch (config) #int VLAN 2 Add an IP address to our VLAN2 to access each other o

One. Test the topology:Two. Test ideas:Three. Basic configuration:A.R1:Interface ethernet0/0IP address 202.100.1.1 255.255.255.0No shutdownIP Route 0.0.0.0 0.0.0.0 202.100.1.2B.R2:1. Interface configuration:Interface ethernet0/0IP address 202.100.1.2 255.255.255.0No shutdownInterface ETHERNET0/1No IP addressNo shutdown2.PPPOE Server configuration:AAA New-modelAAA Authentication PPP Default LocalUsername Cisco password 0

Router#show RunBuilding configuration ...Current configuration:1561 bytes!Version 12.4Service Timestamps Debug DateTime msecService Timestamps log datetime msecNo service password-encryption!Hostname Router!Boot-start-markerBoot-end-marker!Enable Secret 5 $1$6xpi$vgcpvaqgq4vp5chkdvduu.Enable password Cisco!No AAA New-model!Resource Policy!IP Subnet-zero!IP CEFIP

-Negotiate with(can be automatically negotiated or manually configured, the routing protocol cannot be transferred at both ends in the case of Autonegotiation)4 , client (config-if) #ipmtu 1492-------------------- mtu value because pppoe data in encapsulation, A pppoe 8 5 , Client (config-if) #encapsulationppp------------- encapsulated into PPP6 , Client (config-if) #dialer pool7 , Client (config-if) #pppauthentication chap callin8 , Client (config-if) #pppchap hostname admin19 , C

China Mobile's GPRS network uses the APN method to connect to the GPRS device terminal and communicate with the server through the APN. The customer purchased the Cisco 2811 router, and the mobile company needed to pull the optical fiber through the E1 port, I spent more than 1000 RMB with an E1 module. mobile companies are doing very poorly, and optical fiber connectors are not provided at all. I also boug

Implementation of ADSL access using the cisco 2500 router Description: This case is Beijing Telecom's adsl PPPoE access. A common adsl modem and a cisco 2500 router (dual Ethernet port) are required, and IOS 12.2 (15) t, can achieve LAN Internet sharing. in this case, the configuration is divided into seven steps: www.

) #interface gigabitethernet0/0.1Router (config-subif) #encapsulation dot1q 2Router (config-subif) #ip address 192.168.1.1 255.255.255.0DhcpWanglei (config) #ip DHCP excluded-address 192.168.1.1Wanglei (config) #ip DHCP pool dhcppool1Wanglei (dhcp-config) #network 192.168.1.0 255.255.255.0Wanglei (dhcp-config) #default

server has a set callback, the server dials back the phone number that has been set up or asks the user to choose the callback. below is the specific configuration: ------------------------- Access#show Run Building configuration ... current configuration:1833 bytes !version 12.2 No parser cache No service single-slot-reload-enable Service Timestamps Debug uptime Service Timestamps log uptime No service password-encryption !hostname Access ! Access server with Name No logging rate-

When configuring the Cisco 3560 switch in the morning with the Cisco Packet Tracer practice, it is found that the IP address of the port cannot be configured in port configuration mode.Switch>Switch>enableSwitch#configure TerminalSwitch (config) #interface F0/1Switch (config-if) #?DhcpOnly DHCP commands are available. Check on the Internet, the original switch po