dual 10g nic

Simple Type: Cp/etc/sysconfig/network-scriptes/ifcfg-eth0 ifcfg-bond0Device=bond0Bootproto=noneOnboot=yesipaddr=192.168.2.17netsmak=255.255.255.0Type=ethernetVI Ifcfg-eth0Device=eth0Bootproto=yesOnboot=yesType=ethernetMaster=bond0Slave=yes VI Ifcfg-eth0Device=eth0Bootproto=yesOnboot=yesType=ethernetMaster=bond0Slave=yes Vi/etc/modprobe.confAdd to:Alias Bond0 BindingOptions Bond0 miimon=100 mode=1 This means that the link state is detected in 100 seconds, and if one is not,

Article title: Dual-Nic Internet access in LINUX. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. I. network extension structure: Server: set two Nics: Eth1: 192.168.99.26 mask: 255.255.255.0 Gateway: 192.168.99.htm # connect with Inte. Net to connect the vro to the Inte

In Linux, set the tftp service and set the dual NIC-Linux Enterprise Application-Linux server application information. The following is a detailed description. 1. Set up the tftp service in Linux Problems: There is a tftp green software on Windows, so there must be similar software on Linux, So I entered the tftp Command in Linux. Hey, I actually entered the tftp console, so simple ??? After entering the h

276192.168.1.255 255.255.255.255 on the link 192.168.1.100 276192.168.10.0 255.255.255.0 on the link 192.168.10.108 276192.168.10.108 255.255.255.255 on the link 192.168.10.108 276192.168.10.255 255.255.255.255 on the link 192.168.10.108 276224.0.0.0 240.0.0.0 on the link 192.168.10.108 276224.0.0.0 240.0.0.0 on the link 192.168.1.100 276255.255.255.255 255.255.255.255 on the link 192.168.10.108 276255.255.255.255 255.255.255.255 on the link 192.168.1.100 276====================================

Group 1 mode manual[Switch]interface gigabitethernet 1/0/1[SWITCH-GIGABITETHERNET1/0/1] Port link-aggregation Group 1[SWITCH-GIGABITETHERNET1/0/1] Interface gigabitethernet 1/0/48[SWITCH-GIGABITETHERNET1/0/2] Port link-aggregation Group 1[SWITCH-GIGABITETHERNET1/0/2] Interface gigabitethernet 1/0/47[SWITCH-GIGABITETHERNET1/0/3] Port link-aggregation Group 1Test results650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/70/D9/wKiom1W_NnCyuIRnAAOJyZs53EE344.jpg "title=" 8.png " alt= "Wkiom

Article title: Dual-IP settings for Nic placement in Linux. Linux is a technology channel of the IT lab in China. Including desktop applications, Linux system management, kernel research, embedded systems and open source, and other basic categories 1. configure the first IP address in Linux: [Root @ Linux root] # cd/etc/sysconfig/network-scripts [Root @ Linux network-scripts] # vi ifcfg-eth0 DEVICE

Administrator mode cmdRouting Table Interpretationroute print -4Remove default settingsroute delete 0.0.0.0Outside the network, all the wireless, 192.168.0.1 for the wireless gatewayroute add 0.0.0.0 mask 0.0.0.0 192.168.0.1 –pInternal network by, all-in-wire, 192.168.12.1 for wired gatewaysroute add 192.168.0.0 mask 255.255.0.0 192.168.12.1 –p转自：https://zhuanlan.zhihu.com/p/22266906Windows routing table configuration: Dual

CentOS6.5 dual Nic binding tutorial [Root @ localhost] # cd/etc/sysconfig/network-scripts/ [Root @ localhostnetwork-scripts ~] # Ll -Rw-r --. 1 root 149 Aug 3 ifcfg-bond0 -Rw-r --. 1 root 97 Aug 3 ifcfg-eth0 -Rw-r --. 1 root 98 Aug 3 ifcfg-eth1 -Rw-r --. 1 root 182 Aug 3 ifcfg-eth2 -Rw-r --. 1 root 254 Oct 10 2013 ifcfg-lo [Root @ localhostnetwork-scripts] # cpifcfg-eth0ifcfg-bond0 [Root @ localhostnetwork-

module, and modprobe, different, it can be in any path, the need to automatically load the dependent module and bonding into the kernel.View bonding Status' Cat/proc/net/bonding/bond0Ethernet Channel Bonding driver:v3.7.1 (April 27, 2011)Bonding mode:fault-tolerance (active-backup) (Fail_over_mac Active)Primary Slave:noneCurrently Active Slave:eth0MII Status:upMII Polling Interval (ms): 100Up Delay (ms): 0Down Delay (ms): 0Slave Interface:eth0MII Status:upSpeed:unknownDuplex:unknownLink Failure