dual 10g nic

The servers in the company are going to use bonding these days, the main is to do double network card redundancy, the Internet is said the most is the "FreeBSD on the double card binding to improve the bandwidth of the practice", research a bit, the results to everyone said that Linux is very simple, here is not to say, according to the online information on the line. FreeBSD a little bit difficult, engaged in a few days, the initial use of LaGG module, according to the Manual of the "link Aggre

The environment is as follows:Status: A Linux host has two network cards eth0 and eth1, the machine can access the service resources of 192 network, but cannot access 10 network segment resources.Requirement: Linux can access 10 network segment resources through ETH1Routing:Card:Action: Only need to add the following detailed route to access 10 network segment resourcesPostScript: During the operation, I started the idea of adding 10 gateways to let 10 of the packets go eth1.Added to the network

dual NIC Master Standby mode configuration ( bond0 )1Brief IntroductionSet the main standby mode through the dual network card, realize when a network card is down, another network card can automatically replace the work of the network card, to ensure the normal access of networks.2Implement2.1.viewing network card informationExecute ifconfig-a command650) this.w

--------------------------------------------------------------------------------- Dual-network card dual-IP dual-line: some early data centers were not close due to their own technology/equipment. You cannot switch between the routers in the IDC. Only two NICs of one server can be used, and two NICs can be connected to China Telecom/China Netcom respectively. Thi

Ubuntu dual Nic bonding configuration UBUNTU dual Nic binding is very simple, use the following steps: 1. install software apt-getinstallifenslavewww.2cto.com2. modify the configuration file/etc/network/interfacesautoloifaceloinetloopbackifaceeth... Ubuntu dual-

Linux dual-Nic configuration problems are mainly caused by the linux dual-nic. in the afternoon, the two NICs are not connected because the gateway is set and the static route configured manually also has problems, resulting in link failure. reset this evening. Solution to 114 of network problems: www.2cto. cometh0: 17

I. Introduction In Linux, dual Nic binding is implemented by virtualizing two NICs into one Nic. The device combined seems to be a separate Ethernet interface device, in general, two NICs have the same IP address, and parallel links are aggregated into a logical link. In fact, this technology already exists in Sun and Cisco, known as Trunking and Etherchannel tec

your intranet mask, zzz. zzz. zzz. zzz is the address of your intranet Nic. Dual Nic settings: Assume that there is a network segment of 192.168.0.0/24, and the gateway 192.168.0.1 The other network segment is 10.1.0.0/24, and the gateway is 10.1.0.1. Run the following routing command: Route add-p 192.168.0.0 mask 255.255.255.0 192.168.0.1 metric 1 Route add-p 1

off the eth0 Nic with another terminal, Ping does not interrupt [[Emailprotected]etc]#!cacat/proc/net/bonding/bond0ethernetchannel BondingDriver:v3.7.1 (april27,2011) BondingMode:load Balancing (Round-robin) miistatus:upmiipollinginterval (ms): 100UpDelay (ms):0downdelay (MS):0slaveinterface:eth0miistatus: downspeed:unknownduplex:unknownlinkfailurecount:1permanenthwaddr:0 0:50:56:28:7f:51slavequeueid:0slaveinterface:eth1miistatus: upspeed:1000mbpsdu

Existing dual-nic Ubuntu is connected to both internal and external networks Internet Nic eth0, CIDR Block 192.168.63.0 Intranet Nic eth1, network segment 10.147.9.0 Target: other devices on the Intranet, such as 10.147.9.70, that can access the Internet, such as 192.168.63.1. First, you must set the

Dual NIC BindingAdvantages: If one network card is hung off, another network card can be replaced, the normal provision of IPThe premise server is a dual NIC, and on the same mvent1. Edit Vi/etc/sysconfig/network-scripts/ifcfg-bond0Device=bond0Bootproto=noneBonboot=yesipaddr=192.168.1.111netmask=255.255.255.0gateway=19

My centos Server is a virtual machine (installed with centos server) implemented by VMware Workstation on Windows 7. Why should I configure dual NICs for it? Cause 1: The company controls the Internet permissions of the computer and binds the domain account and IP address. Therefore, a network adapter in Nat mode is required in the virtual machine to access the Internet through the host. Cause 2: I need to use SSH to log on to the VM on other c

Bind an IP address to an Internet dual-nic Step 1: Install all Nic driversProgram, You can see one in the Network --> adapter (of course you may not have so many NICs, only two or three), two of which have Internet NICs, because the server is HP and the NIC is already an OEM product, HP 10/100 tx pci Fast Ethernet ada

,time17443msrttmin/avg/max/mdev=6.899/9.417/21.254/3.170ms//用另一个终端手动关闭eth0网卡，ping并没有中断[[emailprotected]etc]#!cacat/proc/net/bonding/bond0EthernetChannelBondingDriver:v3.7.1(April27,2011)BondingMode:loadbalancing(round-robin)MIIStatus:upMIIPollingInterval(ms):100UpDelay(ms):0DownDelay(ms):0SlaveInterface:eth0MIIStatus:downSpeed:UnknownDuplex:UnknownLinkFailureCount:1PermanentHWaddr:00:50:56:28:7f:51SlavequeueID:0SlaveInterface:eth1MIIStatus:upSpeed:1000MbpsDuplex:fullLinkFailureCount:0PermanentHW

Dual Nic questions-general Linux technology-Linux technology and application information. The following is a detailed description. One win7 (dual Nic, 192.168.1.2 (Wireless Nic) and 192.168.2.1) and one RHEL5 (dual

Tags: today database oop name UNIX dual NIC start database man technologyNow is the fashion to the highest level, the deployment of this project, good SQL Server threw it (there is a genuine authorized Enterprise Edition, God ... ), every person will boast: "We are on the top of the Oracle Database system! ”。 Look at the price, it is really very top-level, 600,000, frighten directly did not dare to include

The role of the server's dual Nic is to increase the bandwidth first. If the bandwidth of a NIC is 100 M, the two NICs are 200 M in theory, and the three are 300 M in theory, of course, the actual effect will not be simply increased. However, it is certainly beneficial to increase the bandwidth and maintain the stability of the bandwidth by using multiple network

Now the general enterprise will use dual-card access, so that both the network bandwidth can be added, while the corresponding redundancy can be said to be a lot of benefits. And the general enterprise will use the Linux operating system comes with the network card binding mode, of course, now the network card manufacturers will also be some for the Windows operating system network card management software to do network card binding (Windows operating

Objective: To improve the speed of Samba file sharing with the Virtual Machine Ubuntu. Solution: Ubuntu uses a dual-nic, one bridge is connected to the physical Nic, And the other uses the host-only method to interact with the host for Samba. As shown in: After a virtual network card with host-only access is added, start the virtual machine. In fact, the Sam

1. Bind dual NICs 2. configuration file bound to dual NICs /Etc/sysconfig/network-scripts/ifcfg-bond0DEVICE = "bond0" BOOTPROTO = "static" ONBOOT = "yes" TYPE = "ethernet" IPADDR = x. x. x. xNETMASK = 255.255.255.0BONDING _ OPTS = "miimon = 100 mode = 1 updelay = 600000 primary = eth0" #100 ms health check # mode = 1 is the active/standby mode # primary = eth0 # default active is eth0 /etc/sysconfig/network