gigabit switch link aggregation

# ! Software Version v200r001c00spc300 Sysname it_serverroom # Switch name # # VLAN batch 10 20 30 40 50 60 70 80 90 99 to 100 # Set VLAN # VLAN, batch, 110 # Lacp priority 100 # Link aggregation priority setting # # Undo HTTP server enable # Undo nap slave enable # DHCP enable # enable DHCP # # ACL number 3001 # configure ACL access control # Rule 4 permit TCP s

use the MAC address of Network Card 1. Because mac1 is no longer on the network, the data packets will not be received by any network card. Therefore, after ENI 2 takes over the master role, it is best to have a callback event. When processing this event, it will have a free ARP broadcast and broadcast itself to change the MAC address.Lacp_rate:Send the lacpdu of 802.3ad so that the Peer device can automatically obtain link

: Refers to a number of physical ports bundled together to become a logical port to achieve the load sharing of the output/incoming traffic throughput in each member port, the switch determines from which member port the packet is sent to the peer-to-peer switch based on the user-configured port load sharing strategy.1. Bond interface (supports up to two NICs)nmcliconnectionaddtypebondcon-name bond0ifnamebo

Demonstration of port aggregation configuration and troubleshooting of Huawei switch s5700Huawei port aggregation is divided into two types: manual Load Balancing eth-trunk link and LACP eth-trunk link. I will only introduce the former here. The manual eth-trunk can be regar

VTP (link aggregation Protocol)Vtp vlan TrunkingProtocol VLAN link aggregation protocol in a switching network with multiple switches, the same VLAN is usually configured on multiple switches, and the same configuration is also performed on multiple interfaces, to configure the same VLAN on multiple vswitches, VTP tran

192.168.10.0Network 192.168.20.0 tells neighbors that they know the IPNetwork 192.168.30.0Network 11.0.0.0ar1========================================================================================Interface Eth-trunk3 into Eth-trunk3Undo Portswitch Switch from two-layer mode to layer threeIP address 11.0.0.2 255.255.255.0 set IP to Eth-trunk3#Interface gigabitethernet0/0/0Eth-trunk 3 Add interface to Eth-trunk 3 (

Linux Multi-NIC binding aggregation link-bond technology first, the theoretical partBy bundling multiple Linux network ports into one, you can improve the performance of your network, such as backing up a server that requires you to back up several T data in one night , which can be a serious bottleneck if you use a single gigabit network port. Other applicatio

Tutorial topology: 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M00/47/BF/wKiom1P_THjC8klUAAFlyn6ovHE323.jpg "Title =" 1.png" alt = "wkiom1p_thjc8kluaaflyn6ovhe323.jpg"/> R3 is a gateway, R4 is an egress router, and DHCP is used. R5 is a vro on the Internet. Lab requirements: 1. Three PCs belong to three VLANs 2. R1 and R2 are used for Link aggregation. 3. The Gateway ends at R3 to implement

RHEL7 network adapter link aggregation and grub troubleshooting tutorial, rhel7grub 1. Nic link Aggregation NIC teaming, simply put, is to bind multiple physical ports together as one logical port for higher bandwidth and load balancing or high availability. In RHEL7, runner (which can be regarded as a piece of code) i

The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of ports and enter the port batch configuration view Figure#switchport mode truck will figure p

DTP (Dynamic Link aggregation Protocol)The dynamic link aggregation protocol (DTP) of DTPDTP (dynamic trunking protocol) is a Cisco private Point-to-Point protocol used to dynamically negotiate the port type as Access or Trunk. To complete automatic negotiation, Port 2 must be in the same VTPdomain. The DTP frame is se

Red Hat Enterprise Linux 5-a network interface bound in link aggregation mode cannot use the given DHCP address Define a network interfaceBond0For example, and useIfcfg-bond0The configuration file is as follows: Device = bond0Bootproto = DHCPType = BondingOnboot = YesUserctl = NoBonding_opts = "miimon = 100 mode = 4 lacp_rate = 1 xmit_hash_policy = 1" Two Ethernet devices have been configured to belong to t

/wKiom1mMgJqCROovAAGExf6DHxM640.png "style=" float : none; "title=" screenshot from 2017-08-10 15-37-39.png "alt=" Wkiom1mmgjqcroovaagexf6dhxm640.png "/>650) this.width=650; "src=" Https://s5.51cto.com/wyfs02/M02/9E/36/wKiom1mMgK6AmNL4AAGPuPZvAtI944.png "style=" float : none; "title=" screenshot from 2017-08-10 15-38-49.png "alt=" Wkiom1mmgk6amnl4aagpupzvati944.png "/>650) this.width=650; "src=" Https://s3.51cto.com/wyfs02/M01/9E/26/wKioL1mMgK-x-OhbAADLq9FokPo277.png "style=" float : none; "titl

BondingOptions Bond1 miimon=100 mode=6Note:(1), Miimon is the link monitoring time interval unit is milliseconds, miimon=100 means, every 100 milliseconds to detect connectivity between the network card and switch, such as the general use of additional links.(2), mode=0 means load Balancing mode, two network cards are working, need to support the switchMode=1 means redundancy, Nic only one job, one problem

D-LINK Switch configuration of the network requirements and schematic diagram of the display, for the D-LINK switch setting common command settings, we have discussed, D-LINK switch set networking requirements, the D-

IT experts based on the D-LINK Switch configuration Q A set, now there is a huge controversy about the configuration of the D-LINK switch, there may be people do not know how to configure the D-LINK switch, IT doesn't matter, aft