gnome sniper

The problem solved by the Chinese Input Method of Gnome 3.8 is that manjaro, the operating system currently in use, is based on the arch version. I am using ibus and the specific input method is ibus-sunpinyin. I had been using it quite comfortably a few days ago before the upgrade. As a result, I couldn't help it over the past few days. I upgraded it. This is good, and the input method cannot be used normally. I tried it several times, but I still ca

exchange, as long as not exchange on the self-increment 1[i = 2] Compare 2 and 4, do not exchange, as long as not exchange on the self-increment 1[i = 3] Compare 4 and 6, do not exchange, as long as not exchange on the self-increment 1[i = 4] Compare 6 and 5, exchange, as long as the exchange is reduced by 1Before Exchange [1 2 4 6 5 9][i = 4]After Exchange [1 2 4 5 6 9][i = 3][i = 3] Compare 4 and 5, do not exchange, as long as not exchange on the self-increment 1[i = 4] Compare 5 and 6, do no

From: Http://blog.csdn.net/uunubt/archive/2010/10/22/5958438.aspx Appendix: Indeed, if a beginner in C/C ++ wants to go to VI/vim, it would be too difficult! Here is a Linux IDE. A gnome devdlopement IDE for C/C ++Anjuta-1: 2.30.2.1-1. fc13. System: fedora 13 [Lanux @ localhost --~ -- 13:26] $ uname-SRLinux 2.6.34.7-61. fc13.i686. PAE Installation: [Lanux @ localhost --~ -- 12:21] $ sudo Yum install anjuta *Loaded plug-ins: fastestmirror, presto, r

First, check the operating level of the system and whether the desktop environment is installed1. Use the command runlevel to view the current runlevel.2. Use the command Yum grouplist | more to see if the components of the desktop environment are installed3. Yum groupinstall-y "desktop" "Desktop Platform" "Desktop Platform Development" "Fonts" "General Purpose Desktop 　"Graphical administration Tools" "Graphics Creation Tools" "Input Methods" "X Window System" "Chinese support [zh]" "Internet B

1: In the login screen, press CTRL+ALT+F1, enter console command line mode2: First enter the user name, enter, and then input the password, login success3: Enter the df-h, this command is to view the hard disk space, you can see, your home folder is located in the partition, the space situation, whether it is full. If it is, continue, if not, for other reasons, then find another solution.4: Delete command is RM, delete Folder command can be used RM-RF. Note that there are files or folders that a

Enter the command--wget www.XXX.com in terminal and return the following error: --2012-03-21 14:43:43-- http://www.XXX.com/ resolving 10 (10) ... 0.0.0.10 connecting to |0.0.0.10|:8080 failed:invalid argument Enter the command--curl www.XXX.com in terminal and return the following error: Curl: (7) Failed to connect to 0.0.0.10:invalid argument After Juan Sierra Pons reminder, Echo $http _proxy, found to point to 0.0.0.10:8080. After checking online, this

Gnome-shell: the solution is stuck when the application is switched during development. it is the most troublesome to enter anything. In the first place, only the power was restarted, but the cost was too high. Then I found two better methods. method 1: restart lightdm 1: Press ctrl + alt + F1 to enter terminal mode. Log On As the root user. 2: Run:/etc/init. d/lightdm restart 3: Log On again. Method 2: kill gnome