hard drive ribbon cable to sata

Q: SATA and SATA 2.5, the two specifications of the hard disk performance gap is large? Is it necessary to upgrade the existing SATA hard drive to SATA 2.5? A: The interface is not a p

window and restart your computer. 4. when the system starts, press "F2" (depending on the computer's key) to go To the BIOS settings page and change the hard disk to "AHCI" mode. The general position is: "Devices" → "ATA Drives Setup" → "Configure SATA as" → "AHCI", save and exit BIOS. 5. After the system is restarted, it is successfully modified to the AHCI interface standard. After the above introduction

Install Linux on SATA hard disk (earlier versions)-General Linux technology-Linux technology and application information. For details, refer to the following section. You do not need to read the latest version. Sata hard drive In the BIOS of the motherboard, you must set

Friends who often use hard drives should be very familiar with SATA drives. In fact, in our Win7 system can be very good use of SATA port this function, it can not only speed up the speed of our hard disk transmission, but also to improve the efficiency of the hard

Purchased a piece of Seagate Barracuda 7200.9 160GB Hard drive the day before yesterday, want to optimize SATA hard drive, same as the previous PATA HDD optimization? Technical answer: First, SATA

still a driver! The previous work was done with Vista installer, but now the Vista system files on the hard drive are copied from the Vista installation CD! (The installation of CD-ROM is not brought!) Not the stuff in the previous Vista temp directory ... Know the reason is also good to do, we have to repeat. But this time the object is no longer a Vista temporary directory. But the vista system is the d

prompted successfully, copy the current system file back to its original location to overwrite the original file. This allows us to add our own driver information to the Vista registry. Shutdown restart the computer into the Vista installer, if there is no blue screen, congratulations! Continue to install the program. Automatic reboot to the 2nd time. ----blue screen after reboot! Quickly analyze the cause, n brain cells agree that the problem is still a driver! The previous work was done wit

Article Title: perfect solution for UbuntuLinux shutdown abnormal [SATA hard drive]. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. Shut down or sleep in Linux. When the power supply is cut off, the

Mounting SATA hard disks in linux # fdisk-lDisk/dev/uba: 500.1 GB, 500107862016bytes255heads, 63 sectors/track, running * 5128225280bytesDeviceBoo... Mounting SATA hard disks in linux # fdisk-lDisk/dev/uba: 500.1 GB, 500107862016 bytes255 heads, 63 sectors/track, 60801 cylindersUnits = cylinders of 16065*512 = 8225280

Mounting SATA hard disks in linux # fdisk-lDisk/dev/uba: 500.1 GB, 500107862016 bytes255 heads, 63 sectors/track, 60801 cylindersUnits = cylinders of 16065*512 = 8225280 bytes Device Boot Start End Blocks Id System/dev/uba1 1 60801 488384001 B Win95 FAT32 www.2cto.com 1. kernel compilation, adding support for usb storage devices 2. create a mount point. mkdir-p/mnt/usbhd_hx. Note: You need to mount partitio

If the serial hard disk is hooked up to the interface controlled by the onboard serial control chip, it is easier to set up. Take the P4C800 board PDC20378 serial control chip as an example, connect the serial hard disk and boot into the BIOS. Open the onboard serial controller switch in operating mode under the Advanced menu and set a good working mode. If set to IED, it will enter IDE mode after s