hardware raid card

Operations on RAID can result in data loss, so be sure to back up important data properly before you operate.Name Explanation:Disk Group: A set of disks, which is equivalent to an array, such as configuring a RAID5, which is a disk groupVD: Virtual disk, Virtual disk can not use the full capacity of the array, which means that a disk group can be divided into multiple VDPD (Physical Disk): physical disksHs:hot Spare Hot StandbyMGMT: ManagementPost Pre

1 Preface Every year after the Spring Festival, the university begins, many students return to campus, the market also ushered in the traditional sales season. For friends who have been involved in computer hardware for a long time, in the face of the market many graphics cards, they are very difficult to distinguish one by one, and in the purchase of graphics, it will inevitably fall into some misunderstandings: "High frequency graphics

Installation of MEGACLIBy following the linkhttp://down.51cto.com/data/2042596OrHttp://pan.baidu.com/s/1eQ2FeHcDownload to the Windows Local desktop, and then on the Linux command line command: rz-be, in the Pop-up window select the compressed package that you just downloaded (be careful not to tick the ASCII mode to transfer the file )Tar XF Megacli-8.02.21-1-mdv2012.0.x86_64.rpm.tarRPM-IVH megacli-8.02.21-1-mdv2012.0.x86_64.rpmThe default Yum source wood has, for easy installation, can be manu

A Dell nx3200 NAS storage (Dell r720) cannot enter the system when it is started, and the raid configuration cannot be detected on the raid card configuration page when you press F10 F2 F12 F11. Fault prompt:There are offline ormissing virtual drives with preserved CachePlease check the cables and ensure that all drives are presentPress any key to enter the co

How to add a RAID card driver to WinPE? Teach you a few tricks to get it done. 1, first find Winpe.is_ file, directly change it to Winpe.cab, and then use WinRAR decompression, will find in fact is an ISO, such as: Winpe.iso. 2, find your RAID card driver, generally there is an INF, a sys and a DLL file, and what the

There was a problem with a friend's server recently. After knowing that his server is assembled and configured with a RAID5 array, the system is currently unable to boot properly, and the middle of a power system is off, the data is damaged, RAID is in the process of data repair, but after the replication is complete, the system cannot start. And reinstalling the system will also report the need to format the disk, this time if the direct installation

Windows R2 integrated RAID card driverSome time ago, the company has a new batch of servers, the installation of the operating system found unable to detect the hard disk, it is obvious that the Windows Server installation files do not include the new server RAID card driver, although you can use the server equipped wi

Original http://www.mysqlsupport.cn/megacli-study/ Author: Wu Bingxi Source: http://www.mysqlsupport.cn/contact information: wubingxi # gmail.com reprint please indicate/translator and source, and cannot be used for commercial purposes, offenders must investigate. Megacli common parametersMegacli-adpcount [display the number of adapters]Megacli-adpgettime-aall [display adapter time]Megacli-adpallinfo-aall [show all adapters]Megacli-ldinfo-Lall-aall [display information of all Logical Disk grou

1 IntroductionThe RAID card battery on the server, referred to as the BBU, is a very important component, it has a large impact on the I/O performance of the disk, but the general Bbu power can only be used for 90 days, the system will automatically charge it after the power is exhausted, but it usually takes a few hours to charge, during charging, The cache status of the

Dell PowerEdge Server RAID card driver downloadDell new Array Card driver download Model Support System Driver h310/710/710p/810 Win2008 x32 Windows 2008 x64 Windows 2008 R2 Windows 2012 　 h700/h800 Win 2003 x32 Windows 2003 x64 Windows 2008 x32 Windows 2008 x64 Windows 2008 R2

power-on Boot When you see this interface, press CTRL + C to enter the array card setup interface as prompted (6i card is also the case) Press ENTER directly to enter the next action Use the TAB key to switch to raid Here's how to delete the array power-on Boot The above article is the cloud Habitat Communit

1. Upload the vib Patch Pack650) this.width=650; "Src=" Http://s3.51cto.com/wyfs02/M01/84/02/wKioL1eDSU6wnu1eAADvgAV7NLs436.jpg-wh_500x0-wm_3 -wmp_4-s_2946233798.jpg "title=" 1.jpg "alt=" Wkiol1edsu6wnu1eaadvgav7nls436.jpg-wh_50 "/>2. SSH into ESXi andput ESXi host into maintenance mode3. Query The driver version of the current SCSI RAID card650) this.width=650; "Src=" Http://s3.51cto.com/wyfs02/M02/84/03/wKiom1eDSV-wjV4gAAItIvzt1_U093.jpg-wh_500x0-w

=650; "title=" Pay Me "style=" border-top:0px; border-right:0px; Background-image:none; border-bottom:0px; padding-top:0px; padding-left:0px; margin:0px; border-left:0px; padding-right:0px "border=" 0 "alt=" pay Me "src=" http://s3.51cto.com/wyfs02/M00/78/F1/wKiom1aEyufD6d6OAAC_ Q16vene780.png "" 243 "height=" 219 "/> It's mine: 650) this.width=650; "Title=" my "style=" border-top:0px; border-right:0px; Background-image:none; border-bottom:0px; padding-top:0px; padding-left:0px; border-left:0px;

Wireshark cannot capture wireless network card data Solution The capture session cocould not be initiated (failed to set hardware filter to promiscuous mode) always appears ). Solution: wireshark-> capture-> interfaces-> options on your atheros-> capture packets in promiscuous mode-set it off. The capture session cocould not be initiated (failed to set hardware