how to configure router in cisco packet tracer pdf

Packet Tracer 5.0 Experiment (eight) router static routing configurationFirst, the experimental target Master the configuration methods and techniques of static routing; Mastering the connectivity of the network through static routing method; Familiar with the connection mode of WAN cable; Second, the experimental backgroundSchool has new an

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

) #exit #退出接口配置模式Router (config) #exit # exit Global moderouter#disable# Exit Privileged ModeRouter>Configuring the Router serial interfaceThe serial interface is used to reach the router at the remote site or ISP over a WAN connection.Router>enableRouter#config TRouter (config) #interface serial 2/0Router (config-if) #ip address 192.168.20.100 255.255.255.0Route

Cisco Packet Tracer version: 6.0.0.0045Single-arm routingVLAN planningConfiguration on Switch 0:switch>enSwitch (config) #vlan 2 #创建vlan2Switch (config) #vlan 3 #创建vlan3Switch (Config-vlan) #exitSwitch (config) #exitSwitch#show VLAN #查看vlanSwitch (config) #interface range F0/2-F0/4 #range可以批量选择端口Switch (config-if-range) #switchport ACC VLAN 2 #将这3个端口添加到vlan2里面Swi

software name : Cisco Packet Tracer 6.2 for Windows Student VersionDownload Link:http://pan.baidu.com/s/1bn2WRmR password: J6JWSoftware:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/74/FC/wKiom1YwOl6QeNW5AAXqwnnUQnA621.jpg "title=" 1.png " alt= "Wkiom1ywol6qenw5aaxqwnnuqna621.jpg"/>This article is from the "Piece of Cake" blog, please be sure to keep

Link bundle1. experimental topology :Use Cisco Packet Tracer Simulator ( version 5.3 )650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M01/53/CD/wKiom1RwP62QYgGwAAMePFSVn5I199.jpg "title=" Picture 1.png "alt=" Wkiom1rwp62qyggwaamepfsvn5i199.jpg "/>2. Experimental Requirements:1 Assemble the 3 interfaces of the Sw0 into an interface 2 Assemble the 3 interf

Packet Tracer 5.0 Experiment (ix) router RIP dynamic routing configurationFirst, the experimental target Master the configuration method of RIP protocol; Master to view the routes generated by RIP learning through dynamic routing protocols; Familiar with the connection mode of WAN cable; Second, the experimental backgroundSuppose that the ca

Tags: Linux plugin note ref CER class CISC get HTTPS77652571Https://linux.cn/article-5576-1.htmlTurn on login issues78587383Execute the following script in the root directory of the softwaresudo ./set_ptenv.sh sudo ./set_qtenv.shYou must follow the steps.installed in the default/opt/pt if the fallback is reinstalled on the default path because the home directory is installedSome dependent librariessudo apt install libqt5scripttools5sudo apt-get install libqt5multimedia5-pluginsLinux installed un

First, the experimental topology:Second, the experimental requirements:1, PC0 connection SW1, did not make any changes, see if F0/1 need to wait for 30s to become green;2, SW1 Global deployment of the default port Acceleration command, while the f0/2-5 deployed as Acess port;3, PC1~PC4 connection SW1, accelerate, the second into a green port, shorten the 30s, no longer wait.Third, command deployment:SW1 (config) #spanning-tree portfast Default! []SW1 (config) #int range f0/2-5SW1 (Config-if-rang

Packet Tracer 5.0 Experiment (VII) router one-arm routing configurationFirst, the experimental target Master the single-arm routing configuration method; The communication between different VLANs is realized by single-arm routing. Second, the experimental backgroundAn enterprise has two main departments: Technical department and Sales department

Tags: div forwards cer packet col out log other CISCBuild a network, the left LAN is 10.0.0.0 network segment, right LAN is 12.0.0.0 network segment, the middle is WAN 11.0.0.0 network segmentThe above success, but not very familiar with, the following again1. First create a network with a visual interface2. It seems that the computer must first connect with the switch to connect with the router3. The rest is very simple,

assume that the PC1 computer is selected.1, click the icon, pop up the dialog box, operate as follows, then command the terminal too early.　　　　2, enter in the terminal of the popup:Ping 192.168.1.2 waiting for packets to return resultsPing 192.168.1.3 waiting for packets to return resultsIf it appears as a result, the communication is normal.　　　　　Attention:The way of the hub network has been abandoned by the times, the reason is that the hub sends the packe