how to configure vlan on cisco switch

Layer-3 Ethernet switch: introduces L2 VLAN forwarding, configurations in layer-3 Ethernet switches, MAC addresses, and L2 VLAN forwarding, I hope you will have a clear understanding after reading the following articles. The forwarding mechanism of a layer-3 Ethernet switch is divided into two parts: layer-2 forwarding

(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destination port.(2) Delete imageNo monitor session {S

In the composition of wireless networks, the use of many devices deserves a detailed understanding. Today we will talk about the failure of VLAN wireless Internet access switches. The following is an experience shared by a netizen: A strange problem occurs in the VLAN of the two departments where an office area is located. Some websites on the Internet can be accessed normally, but some websites cannot; ema

Tags: cisco CCNA VLANVLANthe Chinese name is"Virtual local Area network". is a set of logical devices and users, these devices and users are not subject to physical location constraints, can be based on functions, departments and applications and other factors to organize them, communication with each other as if they are in the same network segment, hence the name of the virtual local area network. VLANwork inOSIthe Reference Model2Layer and Section3

C-F6. Multi-VLAN configuration DHCP? C3750-E? CISCO switches, c-f6c3750-e C-F6. Multi-VLAN configuration DHCP? C3750-E? CISCO switches. After VLAN and interface are allocated according to our plan, we need to consider which VLANs need to be configured with the DHCP service.

During hard disk data sorting, we found the original dtp vlan jump experiment video, which includes DTP protocol data packets, test tools, videos, and lazy. The following are the steps. Download the video and watch it. It was very casual. At that time, I kept it for reference. Implementation of VLAN jump attacks I don't talk much about it. I only find such a term on the Internet. No one has told me the

In the wireless network composition, the use of a lot of equipment is worth a detailed understanding. So today we're going to talk about the problem of VLAN wireless internet switch failures. The following is a netizen's experience sharing: Unit one office area where the two departments VLAN appeared a very strange problem, some websites on the internet can be no

A comprehensive case of Cisco inter-VLAN routing and HSRP topology Description: www.2cto.com 1. R3 and R4 simulate the customer's pc, which belong to vlan10 and vlan20 respectively. Vlan10 and vlan20 represent different departments in reality. 2. SW1 is a layer-3 switch, and SW2 is a layer-2 switch. 3. R5 simulates the

trunk protocol, which is an ISL, is also a encapsulation of VLANs, except that this is the Cisco Cisco Private Protocol. Other manufacturers are not available. Switch (config-if) #switchport mode trunk------------------------Set the port type to Trunkswitch (config-if) #switchport trunk Allowed VLAN 1. 2---------Set t

192.168.30.0/24 gateway:192.168.30.1VLAN 192.168.40.0/24 gateway:192.168.40.1Second, the configurationMSW1 three-layer switchMSW1 (config) #ip routing turn on layer three switch routing featureMSW1 (config) #int range fa0/19-22MSW1 (config-if-range) #switchport Trunk Encapsulation dot1q Package 802.1Q protocolMSW1 (config-if-range) #switchport mode trunkMSW1 (config) #vtp domain testMSW1 (config) #vtp mode serverMSW1 (config) #vtp password CiscoMSW1

Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password protection.Switch>enable #进入特权模式

Router and three-layer switch experiment Demo--a gateway that acts as a two VLAN--Hundred dishes background : We know that routers have routing capabilities, so you know how to configure two gateways on a router interface (such as a two VLAN gateway)? Note that it is on one interface instead of two, and we sometimes use the three-layer

interconnected with layer-3 switches. When using a router to connect to a vrovlan, you generally need to set sub-interfaces corresponding to each VLAN on the LAN Interface, while a layer-3 Switch generates a "VLAN Interface" internally )". A VLAN interface is an interface used to send and receive data from each

Configuration example of cisco router and layer-3 Switch environment, cisco layer-3 SwitchSimple environment configuration instance for cisco router layer-3 Switch I. network topology: Ii. configuration command: 1. vro Configuration: Interface FastEthernet0/0 Ip address 10

Experiment topological diagram Experiment Request: Using static route to realize network interoperability, using VTP management VLAN, using three-layer switching technology to achieve VLAN communication. Experiment steps: 1, using Visio to draw a topology map 2. Planning IP Address 3, using packet Tracer 5.0 for simulation experiment. Summary of Knowledge points: This experiment set involves stati

Gigabitethernet 0/0.1 Enter sub-interface Encapsulation dot1q 10 Setting the package typeIP Add 172.26.1.254 255.255.255.0ExitInterface Gigabitethernet 0/0.2 Enter sub-interface Encapsulation dot1q 20 Setting the package typeIP Add 172.26.2.254 255.255.255.0ExitInterface Gigabitethernet 0/0.3 Enter sub-interface Encapsulation dot1q 20 Setting the package typeIP Add 172.26.3.254 255.255.255.0ExitAdd the computer to the corresponding VLAN to obtain

information. ◆ After The VTP password is set, The VTP transparent mode is SW5) No VTP notification is forwarded. ◆ In Version1 VTP without a password, a switch in transparent mode does not forward the received VTP notification to check the domain name and version number) ◆ In Version2 VTP without a password, the vswitch domain name in transparent mode may be different from the vtp server.) The forwarded VTP notification does not check the domain name

I have just been familiar with the basic configurations of the VLAN division experiment of the switch VLAN division configuration (PT simulator). I am not familiar with this knowledge for too long. Please forgive me for any errors, this configuration is for you to learn about the Cisco simulator configuration case. Www

) -------------------------------------------------------------------------------- Add Catalyst 5002 to the domain You need to add Catalyst 5002 To The VTP management domain named cisco and set it to VTP client. It will receive VTP configurations and updates from the VTP server. Note: by default, the Catalyst 5000 series switches are VTP servers. Cat5002> (enable) Cat5002> set vtp domain cisco mode client T

How does a cisco switch find a loop? How to solve Loop Problems, cisco How does a cisco switch find a loop? Loop Problem Solution How can we intuitively and quickly determine whether a loop exists on a cisco