how to make vpn with raspberry pi

-pi/i2c-python-library-3-axis-mems-gyro-itg-3205-with-the-raspberry-pi/ Create the 'i2c _ itg3205.py' script. Pay attention to the location of the script. Make sure that you can reference the downloaded 'i2clibraries' package or add the downloaded Python package to the Reference Path. From i2clibraries import i2c_itg32

To telnet to the Raspberry Pi GUI via vnc, the Raspberry Pi must have a VNC Server service installed on one side, and a few simple configurations are required to make the operation more convenient, as detailed steps below.1. Installing the VNC server component--tightvncserve

(path, O_RDONLY); if (fd 6. gpio flip operation[Main function] int main(int argc, char *argv[]){ int i = 0; GPIOExport(POUT); GPIODirection(POUT, OUT); for (i = 0; i [Makefile] -- the code tab here may display problems. Use the code repository as the main component. # Executable File target = test # dependency target SRCS = gpio-sysfs.c # target file objs =$ (SRCS :. C =. o) # command compiler and options cc = gcccflags =-wall-STD = gnu99 $ (target): $ (objs) $ (CC)-O [e

Implementing a dialogue robot with Raspberry Pi Recently, we have implemented a robot that can talk to people with Raspberry Pi, a brief introduction. Raspberry Pi is the world's most popular micro-computer motherboard, is the le

0. PrefaceThis blog post may not have much use value. But practice for practice. There are many ways to use SQLite on Raspberry Pi, and there are many ways to install it. "1" assumes that Python is used, so you don't have to install SQLite because Python has its own sqlite."2" can be installed using Apt-get. Only the version of SQLite is slightly lower. "3" can be installed using the source code, directly

I have seen a lot of articles to make Raspberry Pi into a wireless AP, but what I want to do today is to make Raspberry Pi into a NAT-enabled router, I did this because I was on a business trip to Holland and found my bambook unab

Original Address: Portal. NET Core on Raspberry PiArm32 builds is available as community supported builds for. NET Core 2.0. There is no SDK this runs on ARM32 if you can publish an application that would run on a Raspberry Pi.These steps has been tested on a RPI 2 and RPI 3 with Linux and Windows.Note:pi Zero supported because the. NET Core JIT depends on ARMV7 instructions isn't available on

The first blog gave me a long course design, that is, the topic "3G wireless router. The development platform used in this development project is the Raspberry Pi Development Board. The following is the question ..... Objective: To set Raspberry Pi as a 3G wireless router and access the Internet through Huawei's e261.

ObjectiveIn the previous article, "Raspberry pi set automatic dialing, build no-line by environment" , the author uses HOSTAPD and UDHCPD programs to create wireless hotspots to achieve address assignment and DNS server settings. This article will make improvements to the Raspberry

We have explained in detail the Raspberry Pi control ultrasonic module ranging (http://www.cnblogs.com/yuemo/p/8888342.html) and ultrasonic control buzzer module audible (http://www.cnblogs.com/ yuemo/p/8906111.html).Today we'll see how to apply all two modules and make an anti-theft device.First look at the connection of each pin (requires seven mother-to-female

d.authoritative;At the bottom of the file add the following lines:Subnet 192.168.42.0 netmask 255.255.255.0 {range 192.168.42.10 192.168.42.50;option broadcast-address 192.168.42.255;o ption routers 192.168.42.1;default-lease-time 600;max-lease-time 7200;option domain-name "local"; option Domain-name-servers 8.8.8.8, 8.8.4.4;}Make the wireless adapter the default for the DHCP request:sudo vim/etc/default/isc-dhcp-serverChange "to INTERFACES="" " INTE

device I'm picking up is a sensor, not a character device, so I need to convert it. Similarly, the annotated Inwaiting () and Flushinput () functions are for character input, and I have not tested them on my machine, because sensor will keep on reporting data, simply read it.Another important aspect of hardware connectivity: The tx of the Raspberry Pi to be connected from the Rx of the device, the Rx of th

/ Designsparkrs/dump1090$ CD dump109 0$ make Then edit the/etc/rc.local file and add the following line before" Exit 0 ": cd ~pi/dump1090; ./dump1090 --net --net-http-port 80 --interactive Run Now that we need to reboot to configure the kernel for the TFT display, the configuration will be blocked if the default TV tuner support is not loaded for the RTL-SDR hardware. If all goes well, dump10

-linaro-arm-linux-gnueabihf-raspbian-x64 are used for 64-bit machines. Each cross-compilation tool has a bin directory in the directory to enter, execute./arm-linux-gnueabihf-gcc-v to view the GCC version. I use ARM-RPI-4.9.3-LINUX-GNUEABIHF here because the GCC version on the board is now 4.9.3 3. Start compiling 3.1 Enter the Linux kernel directory: $ CD ~/RASPBERRY/LINUX-RPI-4.4.Y $ kernel=kernel7 $ make

To make it easier to connect and control the Raspberry Pi over the network, use SECURECRT to connect the Raspberry Pi over the network. 1, on the Raspberry Pi through the terminal comma