how to make vpn with raspberry pi

compile the correct executable file on the Raspberry Pi.2. Compiling third-party librariesIf you want to set the global cc and CXX variables, enter the following command each time you open a new Terminal :1 $export cc=arm-linux-gnueabihf-gcc 2$exportThe other global variables are the same as above.Cross-compiling steps with the following common third-party libraries1>> sqlite3 http://www.sqlite.org/downl

best to ensure that the file contents are shown below.Auto LoIface Lo inet LoopbackIface eth0 inet DHCPAuto Wlan0Allow-hotplug Wlan0Iface Wlan0 inet ManualWpa-roam/etc/wpa_supplicant/wpa_supplicant.confIface Default inet DHCPIf you do not want to set the DHCP dynamic IP, you can also set the static IP, the file contents are as follows:Auto LoIface Lo inet LoopbackIface eth0 inet DHCPAllow-hotplug Wlan0Iface Wlan0 inet ManualAddress 192.168.1.100Netmask 255.255.255.0Gateway 192.168.1.1Wpa-roam/e

The official Raspberry Pi camera Module, capable of shooting 5 million megapixel images and recording 1080p video, uses the CSI interface on the Raspberry Pi board.Installing the CameraFirst make sure that the Raspberry

also to modify the ECB version check, ? unzip and put to ~/.emacs.d/lisp/cedet the. linum.el, download the latest, put to ~/.emacs.d/lisp/. session.el, Download the latest, put to ~/.emacs.d/lisp/. ? Color-theme.el, Download the latest, put in ~/.emacs.d/lisp/. ? session-2.3.a, download, unzip to the ~/.emacs.d/lisp/. ? Then compile all of the above *.el into *.ELC, using Emacs until why do this, where the ECB and Cedet are compiled separately with

and put into the ~/.EMACS.D/LISP/ECB. cedet-1.0.1. Download, do not use 1.1, avoid to change the ECB version number check,? unzip and put to ~/.emacs.d/lisp/cedet the. linum.el, download the latest, put in ~/.emacs.d/lisp/.? session.el. Download the latest, put to ~/.emacs.d/lisp/. ? Color-theme.el, Download the latest. put it on the ~/.emacs.d/lisp/.? session-2.3.a. Download, unzip to ~/.emacs.d/lisp/. ? Then compile all of the above *.el into *.ELC, using Ema

1. Download the latest ROM on the Raspberry Pi website firsthttps://www.raspberrypi.org/downloads/raspbian/Here's the choice: RASPBIAN JESSIE with DESKTOPDate is 2017.7.5Get files after download: 2017-07-05-raspbian-jessie.zipAfter decompression: 2017-07-05-raspbian-jessie2. Prepare the software Win32 Disk ImagerSelect the newly extracted img file, specify the target USB flash drive (recommended to prepare

Port:can ' t read "Build.cmd": Failed to locate ' make ' in Path: '/opt/local/bin:/opt/local/sbin:/b In:/sbin:/usr/bin:/usr/sbin 'Installation is complete.Terminal Input command minicom startup program.This may be an error, possibly/dev/modem:no suchfile or directory.Workaround:Type Minicom-sChoose Serial Port SetupA-Change to/dev/tty.usbserialEnter and select Save Setup as DFLChange the baud rate divisor to 115200, the checksum is set to 8N1Power on

Raspberry Pi is not like the motherboard of the PC with a battery for the timing after the shutdown, each time the board starts to re-time, netizens generally provide the method is to use the Ntpdate network calibration, but the board is not even mobile network, because the mobile firewall will intercept the relevant access.For detailed installation and configuration of this calibration service, there are a

Excerpt from: http://www.phodal.com/blog/user-csharp-develop-raspberry-pi-application/Raspberry Pi C#mono Linux Mono is a free open source project hosted by Xamarin Corporation (formerly Novell, First Ximian). The goal of the project is to create a series of. NET tools that conform to the ECMA standard (Ecma-33

successfully, such as:Try the Internet with your own browser, success! Such as:Second, the terminal configuration1.wpa_gui without the lack of AES encryption, we can solve by directly using our own configuration wpa_supplicant way.1. Edit the/etc/network/interfaces file[Email protected] ~ $ sudo vim/etc/network/interfacesTo make the following changes, please note that reference:#allow-hotplug wlan0#iface wlan0 inet manualauto wlan0iface wlan0 inet Dh

configurationdriver=rtl871xdrvieee80211n=1Hw_mode=Gdevice_name=Rtl8192cumanufacturer=realtekThird, DHCP1. Install the DHCP service to assign IP to each access devicesudo Install Isc-dhcp-server2. Edit the configuration filesudo nano/etc/dhcp/dhcpd.conf3, set the gateway and other information, here is the use of 10.38.10.1default-lease- Time -; Max-lease- Time 7200; log-facility LOCAL7; subnet10.38.10.0Netmask255.255.255.0{Range10.38.10.10 10.38.10.100; option Routers10.38.10.1; option broadcas

Needless to say, Raspberry Pi deployed in the intranet, then there is no public IP address, how to make FTP file transfer through the external network? Let's tell you today with peanut shell Peanut wand port mapping combined with raspberry sent to solve the problem of the method.Peanut Shell website: http://hsk.oray.co

Needless to say, Raspberry Pi deployed in the intranet, then there is no public IP address, how to make FTP file transfer through the external network? Today, we will tell you how to use the port mapping of peanut rods combined with raspberry sent to solve this problem.Here's how it works:1, connected peanut stick2. Lo

Before the text Because recently busy review exam, so did not pick up the Raspberry Pi car, until yesterday, finally empty time to put the code down and share with you. BodyIn the second of the Raspberry Pi Trolley series, there are two ways to define the pin of the R