how to reboot cisco router

The company's GPS patrol system needs to go WVPDN to communicate, but before looking for a telecommunications took a CISCO2811, collapsed once, the 2811 is the telecommunications sent, the estimated quality is not how, and then to find the company to buy the same type of equipment, 2811 discontinued, on the Cisco 2911.Yesterday arrived Ah, excited a bit, super terminal connected on, looked at the system configuration, the result of the hand is cheap,

At present, China's wireless router industry is developing very rapidly, and its market demand is also very high. Here we mainly introduce Cisco's first dual-band wireless router launched in China, this section describes the features and performance of the vro. In May 19, Cisco launched the Linksys by Cisco dual-band w

Initial installation of the CISCO router tutorial During the first installation, the system automatically enters the Dialog Setup, as prompted on the screen, answer the router name, encrypted super login password, super login password, remote login password, dynamic routing protocol, and the configuration of each interface, and save the configuration. After the v

Telnet remote Login Configuration 1, configure Cisco router login account, password, account level, as shown below, account name ABC, password for abc123, account level of 15 (highest level) R1#configure Terminal R1 (config) #username ABC privilege secret abc123 R1 (config) #end r1# 2, configure the Cisco router

we are using Console connect the router and the computer, start the router and use the Putty connect to the router's console ( Console ), it is recommended that you first configure the hostname of the router ( hostname ) To facilitate identification, configure the privileged mode ( Enable ) Password and vty ( telnet ) password to protect the

Test environment: Cisco Router Intranet interface F0/1:192.168.1.1 255.255.255.0 External network Interface f0/0:10.0.0.1 255.255.255.0 Server ip:192.168.1.100 First configure on the router: Router>en #进入特权模式 router#conf T #进入全局配置模式 Enter configuration commands, one

Article Title: simulate a cisco router using dynamic in Linux. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. Environment: centos5.2 Software: dynamic. cisco-ios 1: Download the dynamic binfile. Wget http://www.ipflow.utc.fr/

CISCO Router Network Address Translation (NAT)Tutorial name: Cisco Router Network Address Translation (NAT) objective: to connect all Intranet IP addresses to the Internet using a small number of public IP addresses. Tutorial Introduction: using NAT technology, when an intranet private address sends data packets to a v

Tags: Cisco CCNA router Password managementfor device security, the device administrator typically sets the user name and password for the device. Here's how to configure 3 passwords, with emphasis in the middle.Username Test password Cisco//This is to set up a layer of accounts and passwordsEnable password 123// This is the Setup admin passwordRouter (config) #l

Cisco port status: CSU ── channel server unit, DSU ── data server, unit, DTE ── DataTerminalEquipment 1. Serial * is down, line protocol is down (DTE) faults: [1] No power is added to the vro. [2] LINE is not connected to CSU/DSU. [3] hardware error. Solution: [1] Check power supply. [2] Check whether the cables and serial ports used are correct. [3] switch to another serial port. 2. Serial * is up and line protocol is down (DTE) faults: [1] local or

255.255.255.0 IP nat outside no IP mroute-cache Bandwidth 2000 No Fair-queue clockrate 2000000 Interface Serial1 No IP address shutdown No IP classless IP route 0.0.0.0 0.0.0.0 Serial0 access-list 1 Permit 10.1.1.0 0.0.0.255 Line con 0 line aux 0 Line vty 0 4 password Cisco End 3, multiplex dynamic address conversion applicable environment: Dynamic Address Translation is a dynamic address conversion, but it can all