ide pata hard drive

Many friends have previously asked if the SATA hard drive can use ghost. When using ghost to back up the system, they may have encountered this situation, After the system is started with a floppy disk or a CD, the system is black after the ghost. EXE command is used. Does ghost not support SATA devices? Can't we back up the system after using a SATA hard disk? T

What to do when the hard drive is not found in the WinXP system installation Reason Analysis: The hard drive is not set correctly in 1.BIOS If you do not set the hard drive parameters correctly in the BIOS, you will be prompted

Many catchers have asked if they can use ghost for SATA hard disks. When using ghost to back up the system, they may have encountered such a situation. After starting the system with a floppy disk or a CD, when using ghost. after the EXE command, the system is black and crashes. Does ghost not support SATA devices? Can't we back up the system after using a SATA hard disk? The answer is whether the SATA

) directly affects the normal use of the hard disk. Today's machines support the "IDE Auto Detect" feature, which automatically detects the type of hard disk. When the hard disk type is wrong, sometimes you simply cannot start the system. It is recommended that you check the BIOS settings to see if the

the backup. When files are stored, they are written to contiguous blocks without fragmentation. This is a big job. It may be unnecessary for program partitions that do not change frequently like/usr, but it can create a miracle in the/home partition of a multi-user system. It takes the same time as the disk fragmentation of the Windows NT Server. If the disk performance is still unsatisfactory, there are many other steps to consider, but any hardware solution that includes upgrading or purchasi

Reason Analysis: The hard drive is not set correctly in 1.BIOS If you do not set the hard drive parameters correctly in the BIOS, you will be prompted to not find the hard drive when you install it. 2.

syntax:hdparm [-CFGHIIQTTVYYZ] [-a Supplemental Note:Hdparm can detect, display and set parameters for IDE or SCSI hard drives.Parameters:-a-a-C-C detects the power management mode of the IDE hard drive.-dDiskDMA mode.-F writes the memory buffer's data to the

What to do if the BIOS does not recognize the hard drive: In the first case, the most likely data cable is not plugged in or there is a problem with the data cable. Or the power supply problem, the hard drive is supplied directly from the power supply interface to obtain power. The white is the traditiona

the transfer process, also encounter file protection or whether the file needs to be copied, etc., especially 1TB or more data transfer time can consume a large half day. Is there any way to receive the data of old hard disk once and for all? This is the focus of this topic. Blue screen crashes? One trick. HDD Mode setting Users to buy a new computer, the original old hard disk data to copy, the

Test hard drive Bad Sectors in CentOS Hard Disk status testing tools: smartctl, Badblocks, hdparm You can quickly see whether the hard disk is healthy by using smartctl. The command is as follows: [Root @ qy ~] # Yum installsmartmontools-y Start SMART # Smartctl -- smart = on -- offlineauto = on -- saveauto = on/dev/sd

an idle disk. Do not write new data into the partition to be restored before restoration.This data recovery software supports FAT12, FAT16, FAT32, NTFS, and EXT2 file systems, find the files in the disk after the partition/partition table is damaged or the Ghost is damaged. for deleted files, the software has a unique algorithm to restore files that are considered unrecoverable, And the Directory and file recovery results are very good; it also supports recovery of various storage media, includ

function of the low grid, so the recommended or software to the way to the low-level format of the hard disk. Maxtor produced a low grid tool Low.exe, the software can be maxtor hard disk, in fact, this program can be applied to various brands of various models of IDE hard disk. The operation of the software is quite

Installation system can not find a hard drive solution First of all, we find the reason from the periphery, a hard drive to work first must have a power supply, there is an IDE line with the motherboard. Therefore, do not recognize the

can be resolved. 　　Third failure: A primary partition fails to start the hard drive The hard drive has a primary partition in which the primary partition is started, and if the primary partition is faulty, then the system cannot be booted from the hard

disk. Here, root corresponds to/boot partition (if/boot partition is not specified separately, this root should point to the "/" partition ). Digression (basic knowledge supplement) Hdx, msdosy Hd specifies the hard disk, starting with 0. hd0 indicates the first hard disk, and so on. Msdos specifies the partition on a hard disk. Starting from 1, msdos1 indicates

, you can understand C:/Documents and Settings/Administrator/local in windows.Settings/TEMP directory. Pai_^7. Set the "mount point" by yourself"In Windows, we can use "create folder" to store a class of things, of course, in Linux. In addition to this method, you can also set a "MountLoad point "(in fact, the function is equivalent to setting up a special place to store special things ") There are many others. I will not elaborate on them one by one. The following figure shows the functions of

have built-in RAID features or has been in the BIOS to turn off RAID features, you can not load the driver, directly install the system. Scenario four: Some motherboards from the IDE to the SATA transition period, SATA is turned off by default in the BIOS. You need to manually enable the line. SATA interface: Serial ATA (SATA, serial Advanced Technology attachment), also known as Serial ATA, is the twin brother of serial SCSI (sas:serial attached S

condition. Now the PE in the toolbox comes with MHDD hard disk detection tool, it is important to note that in the motherboard BIOS check the hard disk mode, whether it is the AHCI mode or IDE mode, MHDD is unable to scan the hard drive in the case of AHCI mode Save

A hard disk partition consists of a primary partition and an extended partition, with a maximum of four partitions. If all the IDE Hard Disks are primary partitions and extended partitions, they are hda1, hda2, hda3, and hda4 respectively. If you want to have more partitions, you can perform logical division in the Scalable partitions. The initial partition start

the hard disk is usually set to Cable Select, which can be adjusted as needed. All devices connected to the channel must support the Cable Select function, and all devices connected to the channel must set the jumper to the Cable Select function. 4. If the hard disk uses sound insulation or shockproof insulator, use a taper or patch cord connection between the hard