infiniband nic

CentOS7.1 Nic settings Today, I installed CentOS7.1, and found that it was very different from that before 6. The command changed a lot and the network configuration was not as good as that. Next I will introduce the NIC configuration in 7, including the problems I encountered. After the VM is installed Run ifconfig You will find that the NIC information has

Currently, many organizations have built internal lan. Most enterprise networks use twisted pair wires to connect to NICs for communication. Among them, twisted pair wires generally use 5 types of lines with a transmission rate of 100 MB. There are some differences between NICs. Many NICs adopt 10 Mbps/mbmps adaptive NICs, that is, the transmission rate automatically matches between 10 MB and MB. For such NICs, theoretically, a file of a dozen MB can be transmitted within several seconds, but it

Click Start> set> control panel, double-click Network and sharing center, and then click manage Nic settings on the left ", press ALT in the "Network Connection" folder to display the menu. Select "advanced"> "Advanced Settings", and select the corresponding network adapter under "connection in the order accessed by network services, click the up or down button on the right to set the NIC priority. In fac

Solution CentOS 7.0 vmwarevm has no Nic Environment CentOS: Version 7 [root@net592~] #uname-a Linuxnet5923.10.0-123.el7.x86_64 #1SMPMonJun3012:09:22UTC2014x86_64x86_64x86_64GNU/Linux Problem 1: Vmware cannot identify the NIC, And the VM cannot access the Internet. Problem 2: The vmwarevm cannot bridge the network adapter and prompts that the network cannot be changed to the bridge mode without a host networ

Linux cannot enable Nic: Deviceeth0hasdifferentMACaddressthanexpected. ignoring solves the following error: The Nic cannot be started successfully on linux. when activating a Nic, the following error is prompted. cannotact... linux cannot enable Nic: Device eth0 has different MAC address than expected, ignoring solves

1. the environment describes the virtual machine created in esxi5.5, the system is Centos6.4, the original only one network card, the name is ifcfg-eth0. To achieve network redundancy, log on to VMwarevSphereClient and add a network adapter named ifcfg-eth1 to the virtual machine. 2. dual Nic binding steps: 1. environment description The virtual machine created in esxi5.5, the system is Centos6.4, originally only one

Centos5.5 update Nic driver bnx2version: 2.0.2 Operating system: CentOSrelease5.5 (Final) fault symptom: Nic automatically goes down for no reason. it will not be long before it will automatically go down after restart using servicenetworkrestart, the number of connections is about 200 ,... centos 5.5 Update NIC driver bnx2 version: 2.0.2 Operating system: CentOS

In RedHatlinux, after installing the linux system, set a fixed IP address for the NIC (bound to two IP addresses), and then configure the nic ip address in command mode. The configuration file is usually/etc/sysconfig/network-scripts/ifcfg-interface-namewww.2cto.com1. configure the nic ip address vi/et... In Red Hat linux, after installing the linux system, set a

Whether you are a system engineer, or operations engineer, or database engineer, etc., are likely to encounter the need for network card special naming, this article is based on RHEL6.4 system as an example of how to do NIC name binding, for reference only!Environment: rhel6.4 Operating systemRequirements: Renaming the NIC Eth0 to Public0Step Description:1. View information for the current eth0 NIC2. Write

Study Notes of AM335x (TQ335x) -- Nand NIC Driver porting, am335xtq335x After the sound card driver was transplanted, I wanted to continue and transplant the NIC Driver. However, I did not expect that the kernel maintained by TI is too robust. porting the NIC Driver is as simple as porting the key driver. The same is true for the Nand driver, I will introduce Na

U-boot-2014.10 port 18th days ---- add DM9000 Nic support (2), holiday scheduleModify code Accidentally deleted this blog, and the recycle bin did not save the draft. Now I can write it again! DM9000 itself also has a base address. This base address is bound by the TXD [] (strap pins) pin. The formula is met: IO base = (pin value of TXD []) * 10 H + 300 H TXD [] pins are in 8 state, so I/O base addresses have eight base addresses: 300 H, 310 H, 320 H,

Configure the dual-nic bond IN Centos6.41. Environment Description The virtual machine created in esxi5.5, the system is Centos6.4, originally only one Nic, named ifcfg-eth0. To achieve network redundancy, login to VMware vSphere Client to the Virtual Machine added a nic, Nic name ifcfg-eth1. 2. Dual

After using VMware to clone a virtual machine, the Wakahara host NIC name is Eth0, then the cloned host uses Ifconfig to see only a network card named Eth1.And in/etc/sysconfig/network-scripts/this directory only has ifcfg-eth0 a network card configuration fileThe Ifcfg-eth0 device property is also eth0Then we cannot modify the network address and status of the eth1 displayed in Ifconfig, we need to make the Eth0 configuration file effective in order

Assuming that Eth0,eth1,eth2,eth3 is bound to bond0, the steps are as follows:(1) #vi/etc/modprobe.conf, add the following 2 lines: Alias bond0 bonding options Bonding miimon=100 MoD E=4When mode=0, the corresponding port of the switch does not need trunk, but the Ping Gateway (192.*.*.*) from the node has a large delay. The solution to this problem is to change mode to 4, while configuring the switch corresponding port to turn on link aggregation and bundle as trunk.In the modprobe.conf file,Th