ip sla cisco router

whether you have loaded an IPSec IOS image that supports SSH. In our example, we will use the Cisco IOS command. Run the following command:Router> Show flashThis command displays the name of the loaded IOS image. You can use the result to compare the list of supported features of your supplier.After you verify that your device supports SSH, make sure that the device has a host name and a correctly configured host domain, as shown below:Router> config

I. Overview: In the actual work can often see a strong SSL VPN can bypass deployment, and support routing mode and NAT mode: Router mode requires intranet to VPN assigned address pool address can be router; NAT mode, VPN Client access intranet host, intranet host sees address as VPN interface address, Therefore, the address intranet of the VPN address pool is not required to be routed. If you want to test

Cisco router VLan isolation LAN broadcast packet configuration experiment and summary, ciscovlan 1. Tutorial Description: connect to and set the IP address of the PC according to the network topology. PC1 and PC2 are required to be accessed on VLAN 12, while PC3 and PC4 are accessed on VLAN 34, PC1 and PC2 are interconnected, PC3 and PC4 are interconnected, and V

EnConf tHostname Cisco3800Interface Loopback0IP address 6.6.6.6 255.255.255.0Interface fastethernet0/0Description WANIP address 119.200.27.50 255.255.255.252IP Nat ousideInterface FASTETHERNET0/1Description LANIP address 192.168.6.1 255.255.255.0IP nat InsideIP Route 0.0.0.0 0.0.0.0 113.200.27.49 Telecom Unicom Next hopIP Route 192.168.3.0 255.255.255.0 192.168.6.2IP Route 192.168.4.0 255.255.255.0 192.168.6.2IP nat Pool www 119.200.27.50 119.200.27.55 netmask 255.255.255.252IP nat inside source

-Negotiate with(can be automatically negotiated or manually configured, the routing protocol cannot be transferred at both ends in the case of Autonegotiation)4 , client (config-if) #ipmtu 1492-------------------- mtu value because pppoe data in encapsulation, A pppoe 8 5 , Client (config-if) #encapsulationppp------------- encapsulated into PPP6 , Client (config-if) #dialer pool7 , Client (config-if) #pppauthentication chap callin8 , Client (config-if) #pppchap hostname admin19 , C

Network MapGoal:from Workstation telnet remote switchEnvironment:cisco Packet Tracer650) this.width=650; "class=" Media "src=" Http://www.davis-wiki.com/lib/exe/fetch.php?media=cisco_router:telnet.jpg "/>Condition1:switch 12:workstation 13:network Cable 1SettingsWorkstation SettingsStatic ip:192.168.1.2255.255.255.0192.168.1.1Switch Settings650) this.width=650; "class=" Media "src=" Http://www.davis-wiki.com/lib/exe/fetch.php?media=cisco_router:telnet

" standard at that time, the result hindered people to use the IP address flexibly! Finally, someone boldly asked to cancel the address classification, VLSM was proposed. After this standard is proposed, in no class environment, the subnet mask becomes VL (longer), is no longer a fixed "IP address category specified mask + same subnet mask in the category address segment", so you can write in the form of

In the middle of a Cisco switching network, how do I find out which port of the switch is connected to the IP address of a machine? The most convenient and quick way is to use the User tracking function of the CiscoWorks 2000 LMS network management software. The graphical interface is clear at a glance. If you do not have this software, you can use the following manual analysis method to find the answer: Ex

significance. The following is an example of how to solve the problem through transparent bridging when the Cisco 2610 router IP settings are difficult. The power dispatching department where the author directly fails to configure IP addresses relies on the Energy Management System (EMS) to control the operation of th